How to prevent leaks in a sheet metal roof

A metal roof stays watertight when the covering suits the actual roof pitch. Before buying, check the pitch, the rafter length and the planned roof penetrations. The minimum angle for one sheet model does not apply to all products of similar appearance, including T18 and T35 profiles. On a gentle slope water flows more slowly, so lap lengths, seals and the position of joints matter more. The corrugation height marking alone does not describe the entire roof system.

By |2026-11-14T20:14:43+01:002022-10-10|Knowledge base|Comments Off on How to prevent leaks in a sheet metal roof

How much does a new sandwich panel roof cost once all the details are added?

The cost of a sandwich panel roof should be calculated from the geometry of the roof slopes and the detail design. The price of the panels does not automatically include the eaves, ridge, fasteners, seals or equipment work. An example budget shows how to combine these items and obtain a comparable cost per metre of finished roof, without mixing it with the hall floor area. Let us assume a building with a footprint of 12 × 24 m, i.e. 288 m². After taking into account the pitch and eaves, the designed slopes in the example are 6.25 × 24.4 m each. In total this gives 305 m² of roof. It is this area that must be distinguished from the footprint. Further ordering also results from the covering modules and the cutting of the panels.

By |2026-11-14T12:53:49+01:002022-09-30|Knowledge base|Comments Off on How much does a new sandwich panel roof cost once all the details are added?

Can a metal roof help cut energy use?

In a metal roof, insulation and airtightness do most of the work of limiting heat loss. Tile-effect metal sheets and T18 trapezoidal sheets can both cover a well-insulated loft. On a hall, a suitable sandwich panel can provide an insulated roof in a single unit. PIR insulation offers high thermal resistance at a relatively small thickness. The colour of the covering affects how hot the surface becomes, but it is only one factor in the building’s thermal performance. Thin steel conducts heat readily. Its main role on the outside of the roof is to keep rain out.

By |2026-11-15T00:02:09+01:002022-09-29|Knowledge base|Comments Off on Can a metal roof help cut energy use?

Should verge flashings match the roof or the façade?

The verge flashing sits at the boundary between the roof and the wall. Visually, it can belong to the roof slope or emphasise the façade line. This decision is clearly visible, especially on simple buildings and with strong colour contrast. It is worth making it before ordering the entire set. Verge flashings must at the same time retain their function of protecting the edge. Colour does not solve the problem of an incorrect height, width or position of the flashing. A verge flashing in the shade of the covering can form a coherent outline with the roof slope. A colour close to the façade, in turn, can tie the side leg more strongly to the wall. There is no single correct answer for every building form. What matters is the distance and angle from which the building will be viewed.

By |2026-11-15T03:59:09+01:002022-09-26|Knowledge base|Comments Off on Should verge flashings match the roof or the façade?

What to consider when fitting square gutters to a metal roof

Square gutters stand out for their clean eaves line and fit with many contemporary buildings, yet they do not automatically offer greater capacity. On a metal roof, check above all the system dimensions, the effective roof area, the positioning of outlets, and whether the eaves flashing matches the roof pitch and overhang. Aesthetics depend on the eaves proportions, building size and downpipe routing, so judge appearance together with function. Remember fixings, thermal movement and cleaning, and base the hydraulic selection on the system data and roof layout.

By |2026-11-14T16:52:04+01:002022-09-17|Knowledge base|Comments Off on What to consider when fitting square gutters to a metal roof

What determines the service life of tile-effect metal roofing?

The durability of a metal roof tile depends above all on matching the coating and core thickness to the conditions on the roof, and on correct installation of the entire covering. Rather than looking for one universal number of years, it is worth checking the specific product: the type of metallic and organic coating, its suitability for the given environment, and maintenance requirements. Edges, fasteners, ventilation beneath the covering and the condition of flashings also matter. The number of warranty years is not the same as expected service life. A roof near a forest, industrial plant or coast operates in a different environment from one in quiet, open housing.

By |2026-11-14T16:51:29+01:002022-09-08|Knowledge base|Comments Off on What determines the service life of tile-effect metal roofing?

Laying modular tile-effect roofing from the eaves to the cuts at a roof valley

Before ordering the battens, establish the exact model and variant of the modular metal roof tile, as this determines the batten spacing and fixing method. Check the instructions for the permitted pitch, sheet geometry, laying sequence and connection rules. A similar appearance of two modules does not guarantee identical installation, especially at ends and corners. The documentation should be on site before the support is built. Choose the specific roofing variant and only then plan the work, to avoid corrections and uncertainty at every joint.

By |2026-11-15T03:58:12+01:002022-08-22|Knowledge base|Comments Off on Laying modular tile-effect roofing from the eaves to the cuts at a roof valley

When does a simple structure give a cheaper roof than the cheapest steel sheet?

The cheapest sheet does not always give the cheapest finished roof. Costs rise through numerous bends, short cuts, flashings and difficult access to the roof slopes. Savings are worth seeking in the design of the building form itself. A simple roof with a well-chosen material can make execution easier and reduce waste. However, the required layers, load-bearing capacity and airtightness must be maintained. First establish what is to be created under the roof. An open canopy needs a different arrangement from a heated workshop. In the first case, the profiled sheet alone can be the external covering without a thermal layer. In the second, insulation, airtightness and a method of limiting moisture must also be planned. Comparing these buildings solely by the price of the steel sheet makes no sense.

By |2026-11-14T12:53:41+01:002022-07-10|Knowledge base|Comments Off on When does a simple structure give a cheaper roof than the cheapest steel sheet?

Daylight in a loft: gable windows, roof windows or dormers?

The choice between a gable window, a roof window and a dormer depends on room depth, orientation to the cardinal points and roof shape. Before ordering the roofing, it is worth checking whether light from one end of the attic will reach its centre, how the window will connect with the insulation and the moisture-control layer, and whether overheating protection has been planned. Furniture layout and work areas also affect how the interior is perceived. Leave the final selection to the designer, who will assess the specific rooms.

By |2026-11-14T23:58:39+01:002022-07-06|Knowledge base|Comments Off on Daylight in a loft: gable windows, roof windows or dormers?

PIR or EPS for the roof: how to compare panels in a project?

PIR and EPS are different sandwich panel cores, but the choice should not be reduced to their names. First establish the roof requirements, then compare complete panel configurations. This order shows how thickness affects flashings, how weight interacts with the structure and which properties actually determine the application. A roof sandwich panel has a core bonded to the facings and a profile suited to a specific application. It is not the same as loose insulation board laid on a ceiling. Data for standalone EPS or PIR do not automatically describe the load-bearing capacity and airtightness of a finished roof panel.

By |2026-11-14T12:54:33+01:002022-07-05|Knowledge base|Comments Off on PIR or EPS for the roof: how to compare panels in a project?
Back to top