Comparing insulation materials for a roof

Choose roof insulation to suit the project. A new flat roof and a pitched roof being renovated offer different places for insulation. In a pitched roof there may be room between or below the rafters, or for a continuous layer over the structure. In a flat roof, consider the position of the insulation in the build-up and the pressure it must withstand. Compare declared thermal conductivity and mechanical properties in the context of the complete roof section. PIR boards, mineral wool, XPS and EPS each suit particular conditions.

By |2026-11-15T03:57:43+01:002022-07-02|Knowledge base|Comments Off on Comparing insulation materials for a roof

Metal roof installation costs and what the labour quote should cover

What matters is not the phrase “sheet metal installation” itself, but comparing the full scope of work. Check whether the offer includes the membrane, battens, flashings, gutters and safeguards, and for a renovation also dismantling and repairs. Ask for a quote for a specific roof slope with separately described additional works and a final amount. Two offers with the same unit may describe different tasks, so list the activities first, then the price. Remember that roof geometry, substrate, access and the number of details drive the cost – a preliminary rate given by phone is no substitute for measurement and inspection.

By |2026-11-14T16:51:58+01:002022-06-20|Knowledge base|Comments Off on Metal roof installation costs and what the labour quote should cover

Clay tiles or tile-effect metal roofing for a new house?

Tile-effect metal roofing and clay tiles are best compared before the structure is approved. They differ in weight, format and the way they are worked on the roof. The price of the basic material shows only part of the expense. The choice should also be decided by the shape of the roof slopes, the details, the desired appearance and the conditions for later servicing of the covering. Steel tile-effect metal roofing is considerably lighter than many clay coverings. For example, with a tile-effect metal roofing weight of 4.7 kg/m², a covering of 160 m² weighs around 752 kg. Plain tiles weighing 1.6 kg each at a consumption of 36 pieces per m² give 57.6 kg/m², that is 9216 kg over such an area. This is a comparison of two specific examples, without battens, insulation and accessories.

By |2026-11-14T10:33:05+01:002022-06-16|Knowledge base|Comments Off on Clay tiles or tile-effect metal roofing for a new house?

When is metal roofing a sound environmental choice?

A metal roof can be an environmentally sound choice if it is properly matched to the project. When assessing its impact, you need to consider production, transport, installation, use and the end of life of the materials. Recyclable steel alone does not guarantee an ecological roof. Durability, waste volume, thermal insulation and repair options all matter. A fair comparison calls for similar scopes and data for actual products, since a bare sheet of metal is not the same as a fully insulated assembly.

By |2026-11-14T20:12:00+01:002022-05-31|Knowledge base|Comments Off on When is metal roofing a sound environmental choice?

How to detail a chimney flashing on a trapezoidal steel roof

The chimney flashing must take up the water running down the roof slope and direct it past the obstruction. It must also work together with the layer beneath the covering and with roof movement. That is why you do not start by choosing a sealant. First you need to establish the chimney's position, the shape of the sheet and how the top edge of the flashings at its walls is closed. Measure the chimney and its distance from the ridge. Check where the valleys and the crests of the trapezoidal profile fall relative to its sides. The roof area above the chimney is also important. The more water flows to its rear wall, the more carefully its division to the sides must be planned. A wide obstruction is not automatically handled with the same detail as a narrow one.

By |2026-11-14T10:33:04+01:002022-05-28|Knowledge base|Comments Off on How to detail a chimney flashing on a trapezoidal steel roof

Preparing a roof for winter to reduce the risk of damage

Before winter arrives, remove loose flashings, lifted edges and active leaks, since frost and wind will make each of them worse. Also check that the entire water drainage system is clear, not just the section at the eaves. Inspect the fixings of snow guards, plus ventilation and any signs of moisture inside. Establish safe roof access and a response plan for after a gale or heavy snowfall. Carry out work on coatings before the frost, in conditions that match the material instructions.

By |2026-11-15T03:58:09+01:002022-05-20|Knowledge base|Comments Off on Preparing a roof for winter to reduce the risk of damage

How to locate and repair a leak in a metal roof

A leak in a metal roof is repaired by removing its cause, not by covering the sheet with sealant. Readers should first establish whether the water comes from rainfall or condensation and check where moisture enters the roof layers. The problem often lies in flashings, laps or fixings. The type of repair is matched to the covering and the condition of its coating, and extensive corrosion or a poor detail may require replacing the element. Vapour from inside can condense on cold components, producing widespread damp even without rain.

By |2026-11-14T20:14:00+01:002022-05-14|Knowledge base|Comments Off on How to locate and repair a leak in a metal roof

Choosing modular tile-effect roofing for a mountain-style home

The choice of modular metal roofing for a mountain-style roof depends first on the pitch of the slopes and the project requirements, and only then on the embossing pattern, colour and coating. It is worth checking how the modules are laid out around dormers, valleys and chimneys, and whether a sample confirms the expected texture and shade. Where there are numerous breaks, the possibility of reusing cut-off pieces also matters. Leave the final choice to the designer, who will account for loads and fixing.

By |2026-11-14T20:13:06+01:002022-05-08|Knowledge base|Comments Off on Choosing modular tile-effect roofing for a mountain-style home

How to restore the appearance of a metal roof

First work out what is spoiling the metal roof's appearance: dirt, a surface layer, rust or a bent sheet. Assess it from somewhere you can stand securely, checking where discolouration clusters, where water runs off and whether the sheet edges are damaged. Contamination close to trees may look unlike that near a chimney. A rusty dot can be leftover filings, yet it may also mean the protective layer has been breached. Identify the cause before choosing painting or replacement.

By |2026-11-14T20:13:43+01:002022-04-10|Knowledge base|Comments Off on How to restore the appearance of a metal roof

Choosing a roof colour to suit the façade, windows and setting

First decide which elements of the house will stay unchanged, then match the roof colour to them. In a renovation this may be the brickwork, a stone plinth or the windows; for a new house, prepare a shared set of samples. Check the shade, gloss and texture of the coating in daylight, in sun and shade, and on a formed profile rather than a flat swatch. View the house from the distance it will most often be seen from, and compare the gutter, flashings and soffit. This approach avoids an accidental mix of similar greys or browns.

By |2026-11-15T03:56:25+01:002022-04-09|Knowledge base|Comments Off on Choosing a roof colour to suit the façade, windows and setting
Back to top