About PiVi

This author has not yet filled in any details.
So far PiVi has created 1404 blog entries.

What should you check before specifying a 40 mm roof panel that is 13.5 m long?

A 13.5 m roof panel can reduce the number of transverse joints, but requires a well-planned design and installation. With a thickness of 40 mm, check primarily the building's intended use, the support and the thermal insulation. A dark colour and second grade raise questions about thermal movement and the actual condition of the specific element. A panel 13.5 m long does not mean a roof without supports over that entire length. The purlin spacing is determined from loads, the specific product's tables and the adopted structural system. The core, facings, bearing width, snow load and wind suction all matter. The fixings are also verified.

By |2026-11-14T12:52:38+01:002026-03-26|Knowledge base|Comments Off on What should you check before specifying a 40 mm roof panel that is 13.5 m long?

Why does the watertightness of a standing seam roof depend on the entire roof slope?

The standing seam moves the joint between adjacent strips away from the main plane of water runoff. This is an important advantage, but it does not justify calling every such roof the most watertight. Water can enter at the chimney, a transverse junction or an incorrect eaves detail. The effectiveness of the covering is determined by the entire system: from the substrate to the final flashing. The longitudinal edges are raised above the surface between them. Water flowing down the roof slope moves mainly along the flat strip. In many solutions the fixings remain concealed within the joint. This limits the number of holes in the visible surface, but does not remove the requirements for their correct execution.

By |2026-11-14T10:36:57+01:002026-03-18|Knowledge base|Comments Off on Why does the watertightness of a standing seam roof depend on the entire roof slope?

How to assess the quality of tile-effect roofing sheets

The quality of a metal roofing tile depends on its steel core, corrosion protection, coating and the precision of its pressings. Check the nominal steel thickness, the material and the product documentation, bearing in mind that a measurement of the coating is not the same as the core thickness. Match the sheet's properties to the conditions on your plot. Remember transport, storage and installation too, because an attractive pattern cannot replace damaged protection.

By |2026-11-14T20:13:08+01:002026-03-14|Knowledge base|Comments Off on How to assess the quality of tile-effect roofing sheets

How a wall plate works and why its anchorage matters

The wall plate transfers loads from the rafters to the wall or ring beam and determines the geometry of the roof slopes and eaves. Before installation, check that its cross-section, anchors and connections match the design, and that the timber is separated from damp substrates. Equally important is continuity of insulation at the eaves, since a thermal bridge there reduces attic comfort. Even a lightweight covering will not remedy an anchoring error, so inspection should take place before subsequent layers are laid.

By |2026-11-14T16:50:37+01:002026-03-10|Knowledge base|Comments Off on How a wall plate works and why its anchorage matters

Internal insulation for a new house on the plot boundary

For a wall close to the plot boundary, every centimetre counts, but a thin insulation layer is only part of the decision. The permissible building layout, fire protection and the behaviour of the wall after internal insulation must all be taken into account. The best moment for these decisions comes before choosing the construction and routing the services. The building's position and the wall detail at the boundary require an assessment of the design. Internal insulation does not settle the question of permissible location, openings or the relationship with the neighbouring structure. It also does not give the right to extend flashings, foundations or insulation beyond the land at your disposal.

By |2026-11-14T10:38:24+01:002026-03-01|Knowledge base|Comments Off on Internal insulation for a new house on the plot boundary

How to trace a roof leak and plan the repair

First limit damage inside and ensure safety, then determine whether the water comes from precipitation or condensation. Check whether the leak appears only with rain from a particular direction, during thaw or at low temperature – this helps narrow the search. The damp patch need not lie beneath the damaged covering, as water can travel through roof layers. The inspection should cover flashings, penetrations, laps, fixings and drainage, rather than random application of sealant.

By |2026-11-14T16:51:13+01:002026-02-27|Knowledge base|Comments Off on How to trace a roof leak and plan the repair

How to cost a mineral wool panel wall, including fixings and installation

The price per square metre of a wall panel is not the price of the finished façade. In new construction, edge-closing elements, seals, fixings and installation must be added. It is also worth checking which area is subject to settlement. The calculation below shows the method using explicitly assumed amounts, without presenting them as a current quote. The enquiry should specify the core, thickness, type of fixing, facings and required parameters. For panels with mineral wool, the fire variant and the associated accessories are also important. Prices for two panels of the same nominal thickness may cover different ranges of properties.

By |2026-11-14T10:37:48+01:002026-02-15|Knowledge base|Comments Off on How to cost a mineral wool panel wall, including fixings and installation

How to compare the prices of wall and roof sandwich panels in 2026?

Wall and roof panels must be priced as different parts of a single building envelope. They differ in geometry, accessories and operating conditions, so a single price per square metre for the whole building can be misleading. The comparison method below organises quantities and scope, and the example amounts show the mechanics of the calculation without pretending to be a current market offer. For the wall, state the vertical or horizontal layout, cover width, thickness, facings and openings. For the roof, add the pitch, lengths, transverse joints and rooflights. In both parts, specify the internal conditions and the project requirements. Such a description allows prices to be compared without mixing different products.

By |2026-11-14T12:53:12+01:002026-02-14|Knowledge base|Comments Off on How to compare the prices of wall and roof sandwich panels in 2026?

XPS or mineral wool? Different tasks in one building

XPS and mineral wool restrict heat flow, but they do so as materials with distinctly different structures. Extruded polystyrene is a rigid foam, while mineral wool has a fibrous structure. This gives rise to important differences in application. The colloquial name Styrodur does not describe these properties. A comparison should cover not only thickness but also moisture, loads, and fire and acoustic requirements. A foundation is in contact with the ground, a loft has different moisture conditions, and a partition wall may need to absorb sound. No single material can be identified as the best for all these locations. XPS is selected where its combination of properties matches actual needs.

By |2026-11-15T18:59:42+01:002026-02-06|Knowledge base|Comments Off on XPS or mineral wool? Different tasks in one building

Metal façade cladding: benefits and common installation mistakes

Metal cladding on a façade provides a regular surface and a clear division of the building volume, but it does not itself insulate the wall. Before choosing, check whether the product and detail allow the planned installation direction, and at corners and openings — the quality of flashings and water drainage. Also compare complete solutions: the substructure, coating, fixings and any insulation. If an insulated partition is needed, a sandwich panel is an alternative. Leave the decision on layout and component selection to the designer.

By |2026-11-14T20:11:11+01:002026-02-04|Knowledge base|Comments Off on Metal façade cladding: benefits and common installation mistakes
Back to top