About PiVi

This author has not yet filled in any details.
So far PiVi has created 1504 blog entries.

Trapezoidal steel sheets for cladding and load-bearing decks

Cladding and structural trapezoidal sheets serve different purposes, although both transfer loads to supports. Cladding closes the roof or façade, while structural sheeting can provide a load-bearing base for subsequent layers. When selecting a profile, it is worth checking geometry, thickness, steel grade and support arrangement, not just the name. T18 and T35 do not automatically replace a high profile designed for insulation and waterproofing. The name alone does not prove load capacity, so the sheet's role should be clearly defined in the design.

By |2026-11-14T23:58:21+01:002022-06-13|Knowledge base|Comments Off on Trapezoidal steel sheets for cladding and load-bearing decks

Flat roof costs with PIR: comparing complete roof assemblies

When buying PIR for a flat roof, you must also price in the slopes, fixings and waterproofing. A cheaper board may require a different method of connection to the covering. The comparison should be made for a finished roof with the same function, geometry and scope of service. PIR boards for a flat roof are selected according to how the covering is constructed. Aluminium laminate, glass fleece and bituminised facing are not interchangeable surfaces. A difference in facing can change the adhesive or intermediate layer required. The offer should show the cost of the entire compatible connection. The basis for the comparison is therefore a specified board, the layers above and below it, and the way they are installed. Without this, a price difference does not explain what the buyer actually receives.

By |2026-11-16T02:21:05+01:002022-06-06|Knowledge base|Comments Off on Flat roof costs with PIR: comparing complete roof assemblies

When is metal roofing a sound environmental choice?

A metal roof can be an environmentally sound choice if it is properly matched to the project. When assessing its impact, you need to consider production, transport, installation, use and the end of life of the materials. Recyclable steel alone does not guarantee an ecological roof. Durability, waste volume, thermal insulation and repair options all matter. A fair comparison calls for similar scopes and data for actual products, since a bare sheet of metal is not the same as a fully insulated assembly.

By |2026-11-14T20:12:00+01:002022-05-31|Knowledge base|Comments Off on When is metal roofing a sound environmental choice?

How to detail a chimney flashing on a trapezoidal steel roof

The chimney flashing must take up the water running down the roof slope and direct it past the obstruction. It must also work together with the layer beneath the covering and with roof movement. That is why you do not start by choosing a sealant. First you need to establish the chimney's position, the shape of the sheet and how the top edge of the flashings at its walls is closed. Measure the chimney and its distance from the ridge. Check where the valleys and the crests of the trapezoidal profile fall relative to its sides. The roof area above the chimney is also important. The more water flows to its rear wall, the more carefully its division to the sides must be planned. A wide obstruction is not automatically handled with the same detail as a narrow one.

By |2026-11-14T10:33:04+01:002022-05-28|Knowledge base|Comments Off on How to detail a chimney flashing on a trapezoidal steel roof

Preparing a roof for winter to reduce the risk of damage

Before winter arrives, remove loose flashings, lifted edges and active leaks, since frost and wind will make each of them worse. Also check that the entire water drainage system is clear, not just the section at the eaves. Inspect the fixings of snow guards, plus ventilation and any signs of moisture inside. Establish safe roof access and a response plan for after a gale or heavy snowfall. Carry out work on coatings before the frost, in conditions that match the material instructions.

By |2026-11-15T03:58:09+01:002022-05-20|Knowledge base|Comments Off on Preparing a roof for winter to reduce the risk of damage

Insulating a new garage, outbuilding or seasonal cabin on a budget

Budget insulation starts with determining where and when heat is needed. A car garage, a workshop used in the evenings and a cabin for long weekends have different needs. Dividing the building into zones helps direct money to the right building elements while reducing the risk of moisture and later reworking of installations. An unheated building protects equipment from precipitation and wind, but insulation alone does not ensure a positive temperature inside. In a periodically heated building, the time to reach comfort and moisture after the heating is switched off matter. With continuous heating, losses through all external building elements become more important.

By |2026-11-14T10:38:19+01:002022-05-16|Knowledge base|Comments Off on Insulating a new garage, outbuilding or seasonal cabin on a budget

How to locate and repair a leak in a metal roof

A leak in a metal roof is repaired by removing its cause, not by covering the sheet with sealant. Readers should first establish whether the water comes from rainfall or condensation and check where moisture enters the roof layers. The problem often lies in flashings, laps or fixings. The type of repair is matched to the covering and the condition of its coating, and extensive corrosion or a poor detail may require replacing the element. Vapour from inside can condense on cold components, producing widespread damp even without rain.

By |2026-11-14T20:14:00+01:002022-05-14|Knowledge base|Comments Off on How to locate and repair a leak in a metal roof

What to check before specifying a 100 mm mineral wool wall panel

The 100 mm panel is one variant of mineral wool wall cladding, but thickness alone does not describe its parameters. A new building requires checking the function of the partition, wind, moisture and openings. It is worth comparing several precisely described configurations before this dimension is ordered as a seemingly universal choice. One hundred millimetres refers to the nominal thickness of the panel or core stated in the documentation. It does not define the cover width, the thickness of the steel sheets or the method of fixing. Add these details to your enquiry, along with the coating and colour of both sides. Without this, quotes may relate to different solutions.

By |2026-11-14T10:37:52+01:002022-05-11|Knowledge base|Comments Off on What to check before specifying a 100 mm mineral wool wall panel

Choosing modular tile-effect roofing for a mountain-style home

The choice of modular metal roofing for a mountain-style roof depends first on the pitch of the slopes and the project requirements, and only then on the embossing pattern, colour and coating. It is worth checking how the modules are laid out around dormers, valleys and chimneys, and whether a sample confirms the expected texture and shade. Where there are numerous breaks, the possibility of reusing cut-off pieces also matters. Leave the final choice to the designer, who will account for loads and fixing.

By |2026-11-14T20:13:06+01:002022-05-08|Knowledge base|Comments Off on Choosing modular tile-effect roofing for a mountain-style home

How to restore the appearance of a metal roof

First work out what is spoiling the metal roof's appearance: dirt, a surface layer, rust or a bent sheet. Assess it from somewhere you can stand securely, checking where discolouration clusters, where water runs off and whether the sheet edges are damaged. Contamination close to trees may look unlike that near a chimney. A rusty dot can be leftover filings, yet it may also mean the protective layer has been breached. Identify the cause before choosing painting or replacement.

By |2026-11-14T20:13:43+01:002022-04-10|Knowledge base|Comments Off on How to restore the appearance of a metal roof
Back to top