About PiVi

This author has not yet filled in any details.
So far PiVi has created 1504 blog entries.

IKO enertherm ALU: comparing quotes for the same result

The purchase of IKO enertherm ALU must be based on the full designation of the variant and its intended use in the building element, because a merely similar laminate does not confirm compliance with the design. In the enquiry, state the assembly with aluminium-faced PIR boards and the intended execution result, and in the pricing allow for the thickness, edge, parameters and installation. A difficult point is the penetration of services through the continuous insulation layer, so do not price only the easy field. Include a section drawing that identifies the exact ALU product and shows all necessary protective layers.

By |2026-11-16T02:22:27+01:002024-03-06|Knowledge base|Comments Off on IKO enertherm ALU: comparing quotes for the same result

Mechanically seamed or snap-lock roofing: how the joints differ

The term ‘standing seam roof’ covers several different solutions. Traditional metal strips are closed by folding the edges. A snap-lock panel has a factory-formed joint. A similar appearance of the finished roof surface does not mean the same installation rules. The differences should be established before choosing the substrate, strip lengths and flashings. Adjacent strips have prepared edges that are joined and closed with sheet metal tools. Depending on the system, a single, angled or double seam is used. With a double closure, the edges undergo an additional folding stage. This is not the same operation as pressing down a ready-made snap lock.

By |2026-11-14T10:36:42+01:002024-03-05|Knowledge base|Comments Off on Mechanically seamed or snap-lock roofing: how the joints differ

What determines the service life of an insulated wall panel with a mineral wool core?

There is no single number of years that describes every mineral wool panel. A wall facing a busy road, a sheltered rear wall and a damp interior all perform under different conditions. The durability of a new enclosure should be planned as the interaction of coatings, tight joints and structure, with consideration for later access to important details. Outside, precipitation, solar radiation, pollutants and proximity to sources of salt matter. Inside, humidity, process operations, cleaning agents and temperature must be described. The same building may require different protection for the sheet steel in a dry storage area and in a room that will be regularly washed.

By |2026-11-14T10:37:15+01:002024-03-01|Knowledge base|Comments Off on What determines the service life of an insulated wall panel with a mineral wool core?

Choosing T12 trapezoidal steel sheet for a small outbuilding

A small storage shed also needs a well-thought-out enclosure. T12 trapezoidal steel sheet gives a subtle surface texture and is available in roof and façade versions. The choice should not be based on profile height alone. What matters is the actual cover width, the support conditions, wind, and how water is drained at the doors and plinth. In the T12 designation, the number describes a low profile approximately 12 mm high. In an example solution, the cover width is 1120 mm. The roof sheet has an overall width of approximately 1154 mm, and the façade sheet approximately 1160 mm. The difference results from the edge geometry and profile orientation. These are not universal dimensions for the whole group.

By |2026-11-14T10:36:36+01:002024-02-29|Knowledge base|Comments Off on Choosing T12 trapezoidal steel sheet for a small outbuilding

What goes into a flat roof and when is it a suitable choice?

A flat roof is an assembly with a slight slope that directs water to planned outlets, not a structure without any fall. It is worth checking whether the design provides the slope in the structure or in shaped layers, and whether it accounts for substrate deflections that may create local ponding. Layer order, sealed details and efficient drainage determine durability. Where insulation thickness is limited, PIR boards can help, but the choice of insulation, waterproofing and trapezoidal sheet must follow a single assembly design.

By |2026-11-14T23:57:20+01:002024-02-28|Knowledge base|Comments Off on What goes into a flat roof and when is it a suitable choice?

Which timber connectors are used in a roof structure?

The choice of carpentry connectors is determined by the roof truss design, not by the roofing type alone. It is worth checking what forces a given node must transfer, what the load direction and substrate are, and whether the catalogue load capacity matches the intended installation and fasteners. In an order, a precise description of the fitting matters more than a general term, because similar components may have different parameters. Traditional timber joints and steel fittings serve different functions, so the designer decides on their use.

By |2026-11-14T23:56:46+01:002024-02-27|Knowledge base|Comments Off on Which timber connectors are used in a roof structure?

Choosing starter profiles for different façade plinth details

The bottom line of the façade is seen up close. It shows the accuracy of execution and how the wall connects to the plinth. Starter profiles can help to tidy up this zone, but their cross-section depends on the construction of the cladding. A recessed plinth needs a different solution from one projecting in front of the face. Ground levels and the proximity of doors and gates also matter. The selection should be based on the full cross-section, not only on the expected visible height of the trim. A recessed plinth creates a distinct undercut beneath the façade. A projecting plinth may require its top surface to be covered and water to be drained away from the junction. These situations differ in geometry. They should not be resolved by using the same trim without checking its position.

By |2026-11-15T03:59:12+01:002024-02-27|Knowledge base|Comments Off on Choosing starter profiles for different façade plinth details

Eurothane G insulation costs: materials and finishing work

The price of Eurothane G covers the composite product, but not the entire insulation service. The cost estimate must include preparing the wall, fixing and finishing. Only such a scope can be reliably compared with the variant in which insulation and lining are carried out separately. Recticel Eurothane G consists of a PIR board faced on both sides with a gas-tight facing and 12.5 mm plasterboard. It is intended for suitable internal insulation applications. An enquiry for PIR boards should describe the internal wall lining that connects Eurothane G PIR with 12.5 mm plasterboard. The masonry beneath Eurothane G must be prepared in accordance with its condition and the requirements of the new build-up.

By |2026-11-16T02:21:55+01:002024-02-21|Knowledge base|Comments Off on Eurothane G insulation costs: materials and finishing work

C-sections for future alterations: preparing building walls for business growth

A company may need a larger gate, additional rooms or a new production line after a few years. It is worth discussing these plans already during the design of the hall. C-section profiles can be a useful element of its walls and substructure. However, they do not provide unlimited freedom for reconstruction. Cold-formed profiles can be well prepared for anticipated changes if it is known what is to change and what loads may arise. The arrangement of columns, rails and panels determines the available places for openings and partitions. It is worth checking where a gate or passage may be created in the future. This does not have to mean making all openings straight away. It does, however, allow a layout to be chosen that does not conflict with the actual plan. This is more advantageous than later cutting out a random section of the substructure.

By |2026-11-15T18:56:24+01:002024-02-20|Knowledge base|Comments Off on C-sections for future alterations: preparing building walls for business growth

Budget for a metal picket fence: how do you calculate the cost of the whole project?

A fence quote is easily underestimated if only the visible pickets are counted. Supports, connections and labour are also needed for the project. A new fence has a different scope from replacing the infill. Instead of looking for a single universal price per metre, it is better to create a clear budget. Every item should come from the same design and a clearly described quantity. Record the run length, heights, number of bays, the gate and the pedestrian gate. Determine whether the structure already exists. If it does, an assessment of its condition and any repairs must be included. New metal pickets do not remove the cost of bringing the support into proper condition. It is worth identifying this before comparing options.

By |2026-11-15T18:59:11+01:002024-02-16|Knowledge base|Comments Off on Budget for a metal picket fence: how do you calculate the cost of the whole project?
Back to top