About PiVi

This author has not yet filled in any details.
So far PiVi has created 1504 blog entries.

What roof dimensions are needed for cutting tile-effect metal roofing?

To order made-to-measure tile-effect metal roofing, you need a drawing of the actual roof slope. The floor area of the house alone is not enough. You need to know the lengths along the slope, the widths, the diagonals and the position of obstacles. Add to this the terminations at the eaves and ridge. It is best to establish these data with the installer before approving the sheet list. The roof is pitched, so its length along the slope differs from the horizontal projection. In a simple example, the horizontal section is 3.9 m and the height difference is 2.1 m. The slope length is approximately 4.43 m, because we calculate the square root of the sum of 3.9² and 2.1². Ordering a sheet 3.9 m long would therefore be clearly too short.

By |2026-11-14T10:37:00+01:002024-05-12|Knowledge base|Comments Off on What roof dimensions are needed for cutting tile-effect metal roofing?

What determines the type and cost of a timber roof frame?

A roof truss is a system that transfers loads from the covering and roof layers to the building's supports. When assessing it, check whether the span, roof shape and attic plan have been taken into account, not just the common name of the roof. Attention should cover load-bearing capacity, stiffness and spatial stability, including during assembly. Acceptance takes place before the structure is concealed by the covering and interior finishes. Cost depends on the quantity and grade of timber, connectors and assembly, not on the type of covering alone.

By |2026-11-14T23:56:26+01:002024-05-10|Knowledge base|Comments Off on What determines the type and cost of a timber roof frame?

Which covering will protect a flat roof?

The choice of flat roof covering depends on compatibility with the substrate, falls, loads and intended use, not on the material name alone. Check that the design identifies the lowest points and emergency drainage, especially with a parapet. Confirm that the waterproof layer suits the fixing method and the PIR board facing. Also verify that outlets, penetrations and corners have execution details and that service access is planned. These details often determine the durability of the whole system.

By |2026-11-14T20:11:14+01:002024-05-04|Knowledge base|Comments Off on Which covering will protect a flat roof?

T18 and T35 roof sheets: matching the profile to the roof

The choice of trapezoidal sheet for a roof depends on matching the profile to the supports, loads and building conditions, not on the number in the name alone. When comparing T18 and T35, check the steel thickness, cross-section geometry, coating, pitch and method of joining sheets. The designations refer to families of sheets with a specific rib height, but they do not guarantee identical geometry across suppliers. Differences in flange width, pitch and cover width can affect the cutting plan and number of sheets, so a specific product data sheet must be used in the design.

By |2026-11-14T23:57:44+01:002024-04-19|Knowledge base|Comments Off on T18 and T35 roof sheets: matching the profile to the roof

How to lay modular tile-effect metal roofing

The key is to check the roof geometry and confirm that the delivered material matches the documentation before laying begins. Compare the model, coating, colour and condition of the sheets, then inspect the pitch, diagonal equality, eaves line and the plane of the battens. These parameters determine the layout of every row and whether the locks will engage without forcing. Before installation, it is worth making a trial connection of several elements on a flat surface. Remember that a small sheet makes work easier but does not forgive incorrect laps.

By |2026-11-14T16:51:15+01:002024-04-17|Knowledge base|Comments Off on How to lay modular tile-effect metal roofing

Which modern construction methods are worth considering?

Modern construction is not about choosing the newest products, but about matching the degree of prefabrication to the specific project. Before deciding, check access, transport and the ability to store large elements. A solution that is quick on a large site may be troublesome on a cramped plot. A sandwich panel requires the correct arrangement of supports and connections, and the core type is selected for the expected parameters. The core name alone does not guarantee the safety of the entire wall. What counts is the classification of the specific partition and how it is made.

By |2026-11-14T16:51:27+01:002024-04-13|Knowledge base|Comments Off on Which modern construction methods are worth considering?

Tile-effect steel sheets or concrete roof tiles: how do they compare?

Comparing metal roofing sheets with concrete tiles should be based on the specific roof, not on covering weight alone. Metal sheeting is lighter and comes in cut sheets or modules, while concrete tiles are small, heavier elements. Start by checking the structure and geometry of the roof slopes, especially during renovation, where the condition of the trusses and connections determines whether reinforcement is needed. Also analyse the drawn covering layout with ridges, corners and flashings, and compare complete systems, not just the base material.

By |2026-11-14T20:13:24+01:002024-04-11|Knowledge base|Comments Off on Tile-effect steel sheets or concrete roof tiles: how do they compare?

Cold-formed steel sections: preparing an enquiry for a quick quote

A precise enquiry saves time for both parties to the order. The supplier does not have to guess parameters, and the client receives quotes that are easier to compare. Cold-formed profiles are best described as specific parts for a defined task. Z-sections, C-sections, sigma and omega profiles require more data than just the name and the total linear metreage. A well-prepared list helps move from a general idea to a predictable delivery. It is worth attaching a drawing with the height, flange widths and bends. The sheet thickness is also needed. For sigma profiles, the shape of the web matters, and for omega profiles, the width of the central part and the flanges. A Z-section may have different flanges on either side. The full geometry makes it possible to establish which product is meant without having to interpret an abbreviation in the message.

By |2026-11-15T18:58:41+01:002024-03-17|Knowledge base|Comments Off on Cold-formed steel sections: preparing an enquiry for a quick quote

Extending a steel building while the plant stays in operation

Extending a steel hall in an operating plant involves two schedules. One covers construction, the other production and deliveries. Reconciling them requires determining in advance the points where the works will intersect with the company's day-to-day operations. A shutdown cannot always be avoided. Its scope can, however, be planned, and people, goods and building services can be prepared for the next stages. The documentation should show the actual layout of frames, bracing, foundations and envelope. Changes made after the original construction must be taken into account. The steel hall may have acquired additional services, gates or equipment. What looks like a free zone in the old design may today be an important part of the process.

By |2026-11-15T03:58:55+01:002024-03-15|Knowledge base|Comments Off on Extending a steel building while the plant stays in operation

T18 or T35 trapezoidal steel sheet for a canopy roof?

The choice between T18 and T35 depends primarily on the support spacing and loads, not on the roof area alone. To decide, establish the dimensions, pitch and support layout, then check the distance over which the sheet spans between purlins or battens. Local snow and wind loads, fixings, anchoring and drainage must also be taken into account. Condensation should be addressed separately. The design of the whole structure, including columns and connections, remains the designer's task.

By |2026-11-14T16:52:02+01:002024-03-15|Knowledge base|Comments Off on T18 or T35 trapezoidal steel sheet for a canopy roof?
Back to top