About PiVi

This author has not yet filled in any details.
So far PiVi has created 1504 blog entries.

Safe access to the roof and safe routes across it

Many roof defects are visible from the ground or from inside the loft. A displaced flashing, an overflowing gutter or a water stain can be photographed from a safe position. Those photographs help a roofer decide where a closer inspection is needed. For access to a chimney or a piece of equipment, the whole route from the roof entry point to the work area matters. A professional can assess the supports and the condition of the covering, select fall protection and check the positions of roof steps or walkways. Rain affects grip on sheet metal. A ladder and grippy footwear alone do not provide adequate protection.

By |2026-11-15T03:56:29+01:002024-10-09|Knowledge base|Comments Off on Safe access to the roof and safe routes across it

How many spare metal fence pickets should I order and how should I choose parts for later?

A few additional items can make future fence repairs easier. However, a reserve only makes sense if it matches the pickets actually installed and is stored properly. There is no single percentage that suits every project. A fence with one length has different needs from a layout with multiple dimensions. It is worth defining the reserve after calculating the basic order. First, calculate the material needed to complete the project. Each section should have a defined number of pickets and lengths. Only then consider additional items. The reserve should not mask measurement uncertainty or replace checking the extreme gaps. Otherwise, it is difficult to assess what actually remained after installation.

By |2026-11-15T18:59:25+01:002024-10-07|Knowledge base|Comments Off on How many spare metal fence pickets should I order and how should I choose parts for later?

Fibre cement on steep roofs: corrugation patterns and roof geometry

On a steep roof, the covering is a highly visible part of the building. Fibre cement sheets create a regular pattern of corrugations and horizontal laps on it. Asbestos-free fibre cement can emphasise the proportions of a simple volume if the format and finishes are chosen deliberately. A steeper pitch does not remove the requirements for support, fixing and safe handling. The more the roof is exposed in the view of the building, the greater the importance of the material's rhythm. It is worth assessing it from the level of the entrance, the street and neighbouring buildings. From these places, other parts of the roof slope are visible. The design should take into account the actual observation points, not only an attractive view from above. The corrugation creates bands of light and shadow whose intensity changes over the course of the day.

By |2026-11-16T02:19:49+01:002024-10-07|Knowledge base|Comments Off on Fibre cement on steep roofs: corrugation patterns and roof geometry

Are concealed gutters suitable for a metal roof?

Concealed gutters can work with a metal roof, provided the eaves detail has been designed for that arrangement. Rather than a generic recommendation, it is worth checking above all the intended emergency overflow path and realistic access for cleaning and inspecting the outlets. A cover changes the appearance but does not replace the required capacity or maintenance. It is also worth establishing how water from the underlay is drained and whether it might accidentally be combined with water from the covering. The decision is best made together with the roof and façade, since later adaptation may require rebuilding several layers.

By |2026-11-14T16:51:46+01:002024-09-15|Knowledge base|Comments Off on Are concealed gutters suitable for a metal roof?

What is a 60 mm mineral wool panel suitable for, and can 40 mm be ordered?

The 60 mm thickness appears in selected wall panel families with mineral wool, but it is not a universal minimum for all systems. A 40 mm version should not be assumed simply because that dimension exists with a different core. First establish the function of the wall, then check the actual range of the product offered. An insulation panel with mineral wool and a sandwich panel with two metal facings are different products. A thin layer of insulation may appear in many systems, but that does not prove the availability of a self-supporting panel of the same thickness. In your enquiry, state the type of element explicitly.

By |2026-11-14T10:37:51+01:002024-09-13|Knowledge base|Comments Off on What is a 60 mm mineral wool panel suitable for, and can 40 mm be ordered?

Comparing three photovoltaic roof quotations without guesswork

Three final amounts are not enough to choose if each offer describes a different scope. First they must be brought to a common scope, and only then can price, energy and service be compared. With an integrated roof, the covering function and the details also matter. A simple table with a few groups of information makes differences visible. It does not require assigning seemingly precise points to things that have not yet been clarified. Every contractor should work from the same geometry, location and description of needs. If one offer was prepared after a measurement and another from an approximate area, this must be noted. It is worth asking for clarification before assessing.

By |2026-11-15T19:00:32+01:002024-09-11|Knowledge base|Comments Off on Comparing three photovoltaic roof quotations without guesswork

PIR for façades: how to price the board together with the system and details

The price of the wall board does not cover the whole façade. In an ETICS system, compatible render layers are needed, and in a ventilated façade a suitable supporting substructure is required. PIR is best compared together with the costs of reveals, window sills and the junction with the remaining thermal insulation. PIR boards can form a continuous insulation layer on the outer side of the wall. This position helps to reduce thermal bridges caused by structural elements. The price of the regular field therefore does not reflect the full labour input. The façade bill of quantities should show both the area and the length of the relevant terminations. Reveals, corners and the roof junction require additional operations.

By |2026-11-16T02:21:08+01:002024-08-29|Knowledge base|Comments Off on PIR for façades: how to price the board together with the system and details

How concealed gutters work and when to choose them

A hidden gutter system is several different solutions, not a single product. Before choosing, check the drawing of the specific variant, because the same name may cover different configurations. Decide which elements are to be concealed, and plan water drainage, cleaning access and insulation continuity. This is easiest at the house design stage. Tightness and the ability to inspect are as important as the appearance of the roof-to-wall junction.

By |2026-11-14T20:12:19+01:002024-08-16|Knowledge base|Comments Off on How concealed gutters work and when to choose them

How panel length affects the weight and handling of mineral wool wall panels

The mass per square metre helps compare panels, but on site a specific piece is lifted. A long panel can weigh considerably more than a small sample suggests. In a new building, the weight calculation must be combined with the support design, the choice of equipment and access to the installation location. The configuration of both facings is also important. The mass may be given in kg/m² or in kg/linear metre for a specific module. In the second case, a linear metre does not mean a square metre unless the cover width is exactly one metre. This difference is worth checking before compiling loads and ordering transport.

By |2026-11-14T10:37:46+01:002024-08-15|Knowledge base|Comments Off on How panel length affects the weight and handling of mineral wool wall panels

How do you compare two prices for steel sheet when sellers quote different metres?

The price per square metre is only useful once you have clarified which metre the seller is billing. The total sheet width is greater than the coverage width. Two different rates may therefore relate to a similar material cost. Instead of comparing the numbers alone, calculate the same list of sheets and add all mandatory order costs. Begin the comparison by identifying the steel sheet. The profile, steel thickness, type of coating and ordered colour should match. Also establish whether the sheet has an additional layer on the underside. A similar photograph and the same trapezoidal height are not enough. Two cross-sections may have a different coverage width and different load-bearing properties.

By |2026-11-14T12:53:45+01:002024-08-11|Knowledge base|Comments Off on How do you compare two prices for steel sheet when sellers quote different metres?
Back to top