+48 500 409 109

Planning repairs to damaged steel building cladding

A dent at the gate, a scratch on a panel or a rain streak do not mean the same type of problem. Repairing the cladding of a steel hall must begin with identifying the damage. Painting over the mark may improve the appearance, but it does not always restore the tightness and properties of the element. It is also important to determine the cause so that the same damage does not reappear. A sandwich panel consists of facings and a core that work together to carry loads. Surface damage does not necessarily mean the loss of all properties, but a deep dent requires a broader assessment. In a steel hall, the extent of the damage, its position relative to the supports and the condition of the connections must be checked. The colour of the mark alone does not determine the repair method.

By |2026-11-15T03:58:39+01:002026-08-15|Knowledge base|Comments Off on Planning repairs to damaged steel building cladding
Read More

How an eaves flashing guides water into the gutter

The over-gutter strip directs water from the roof slope into the gutter and protects the roof edge from seepage, so its shape must suit the covering, pitch and gutter position. Check the bend geometry and its placement relative to the gutter, as these determine effectiveness rather than the metal strip alone. Also account for drainage from the underlay and the ventilation inlet, so water from the underlay does not end its run on timber or insulation. Separately, distinguish the over-gutter strip from the under-gutter strip, which shields a different part of the eaves.

By |2026-11-14T23:58:00+01:002026-08-14|Knowledge base|Comments Off on How an eaves flashing guides water into the gutter
Read More

How do you calculate the cost of a photovoltaic roof over its entire service life?

The purchase price marks the start of the investment, but not its full cost. A photovoltaic roof will require servicing, and some equipment may need repair or replacement. At the same time, it serves as the roof covering and generates energy. A reliable comparison should cover both functions over the same period. There is no need to build a complicated model, but it is worth explicitly recording the costs, benefits and uncertain assumptions. Choose a common horizon for all the variants under consideration. Do not compare one solution over a short period and another over the entire expected life of the building. A distinction must also be made between the warranty period and the durability of each component. The covering, the active elements and the electronics do not have to share an identical service history.

By |2026-11-15T19:00:00+01:002026-07-23|Knowledge base|Comments Off on How do you calculate the cost of a photovoltaic roof over its entire service life?
Read More

EPS, XPS or PIR: how to choose insulation for different parts of a new home?

In a new home, various insulation materials can be used if each one matches the conditions of its zone. A wall under render, a roof under a membrane and a floor loaded with equipment do not impose identical requirements. A comparison of EPS, XPS and PIR is worth starting with the function of the layers, and only then comparing lambda, thickness and the cost of the finished installation. List the walls, plinth, floor, roof and any terrace. For each location, note contact with water, the expected load and the available space. Add the requirements for fire and the method of fixing. Such a schedule shows why one material does not have to be the best choice in every zone.

By |2026-11-14T12:52:21+01:002026-07-08|Knowledge base|Comments Off on EPS, XPS or PIR: how to choose insulation for different parts of a new home?
Read More

How to compare metal fence picket quotes when each one shows a different price?

The lowest number in a quote does not necessarily mean the lowest cost of a finished fence. The price may relate to a piece, a metre of picket or another scope. Different coatings and accessories are added to this. It is therefore worth starting the comparison by standardising the data. Only then can you assess which proposal meets the needs. Sheet metal pickets should be compared as specific products, not similar photos. Prepare one fence description and send the same data to the quotes being compared. Specify the numbers, lengths, layout and finish. If one proposal is based on a different spacing, ask for clarification. A different number of pickets changes the price even for the same boundary length.

By |2026-11-15T18:58:45+01:002026-07-05|Knowledge base|Comments Off on How to compare metal fence picket quotes when each one shows a different price?
Read More

Where does a roof slope need a ventilation outlet?

A roof-slope ventilation element is needed when the design or the covering instructions require supported airflow within the roof layers, especially on a long slope or where a window or chimney interrupts the channel. It does not replace a clear inlet and outlet. Before choosing, check that the gap has an inlet, an unobstructed route and an outlet, and that the element matches the covering profile and roof pitch. Its location follows the design and instructions, not a general rule.

By |2026-11-14T23:57:14+01:002026-07-01|Knowledge base|Comments Off on Where does a roof slope need a ventilation outlet?
Read More

In what order should the panels be installed so that the walls and roof form a tight envelope?

A tight envelope is created by following the correct sequence of work on the walls, roof and openings. Simply screwing the panels to the steel is only part of the job. The base must be prepared beforehand, the sealing layers joined and access left to areas that will later be covered by flashings. This allows subsequent teams to work without redoing completed sections. On the envelope drawing, mark out the wall sections, the laying direction and the working zones. Indicate which elements must be installed before the panels: base rails, tapes, parts of the flashings and the substructures for openings. Adapt the sequence to the chosen system. There is no single rule that in every building you always start with the same building element.

By |2026-11-14T12:52:55+01:002026-06-26|Knowledge base|Comments Off on In what order should the panels be installed so that the walls and roof form a tight envelope?
Read More

How do you fix sandwich panels to a new masonry wall?

A masonry wall can serve as a substrate for sandwich panel cladding, but it does not remove the need for a fixing design. The masonry must be assessed, the load path determined and the space between the layers resolved. On a new building, anchoring and openings can easily be planned in advance. This helps avoid random spacings and repairs to freshly completed façade. The type of masonry units, their strength, voids, mortar and the quality of workmanship all matter. A fixing chosen for concrete is not automatically suitable for hollow block masonry. The design must specify the loads, the substrate and the permitted anchoring solution.

By |2026-11-14T12:52:42+01:002026-06-24|Knowledge base|Comments Off on How do you fix sandwich panels to a new masonry wall?
Read More

Buying sandwich panels in 2026: seven decisions that affect the final bill

Savings on sandwich panels start with project coordination. The price per metre is one element, alongside cutting patterns, partition requirements and installation method. Seven decisions made before ordering allow equivalent variants to be compared and limit expenses that usually appear only after purchasing the material. Separate the wall area from the area of purchased panels. The covering module, openings and shape of the last field determine the number of elements. An allowance adopted without a drawing may be too small on a complex façade or unnecessarily large in a regular layout. List lengths and quantities instead of rounding the square metreage alone.

By |2026-11-14T12:53:10+01:002026-06-17|Knowledge base|Comments Off on Buying sandwich panels in 2026: seven decisions that affect the final bill
Read More

How much should you budget for a house with sandwich panels and what does the cost cover?

The price of a house with sandwich panels must be calculated from the scope of the finished building. Square metres of panels do not include foundations, structure, windows or services. Before comparing quotes, it is worth breaking these parts down separately and defining the finishing standard. Only then does a lower cladding price matter for the overall budget. Let us assume a single-storey house with 100 m² of usable floor area, a compact form and a simple roof. Sandwich panels form its designed cladding on a separately selected structure. This is a calculation assumption. Not every panel family is intended for such an application, and the structural system must correspond to the house design.

By |2026-11-14T12:54:15+01:002026-06-17|Knowledge base|Comments Off on How much should you budget for a house with sandwich panels and what does the cost cover?
Read More
Back to top