About PiVi

This author has not yet filled in any details.
So far PiVi has created 1504 blog entries.

Why must sheet thickness be selected together with the profile and supports?

There is no single sheet thickness suitable for every roof. The sheet works together with the ribs, supports and fasteners. The choice of 0.5 or 0.7 mm should follow from the load and the specific section. Thicker material can improve the properties of the system, but it will not fix faulty construction or incorrectly selected fasteners. It must be established whether the stated value describes the nominal steel thickness and according to which rules it has been declared. Protective coatings are separate layers. Measuring the total thickness of the finished sheet does not automatically separate them from the core. Therefore, simply applying a calliper does not replace identifying the material.

By |2026-11-14T12:53:32+01:002023-01-03|Knowledge base|Comments Off on Why must sheet thickness be selected together with the profile and supports?

What changes when you choose trapezoidal steel sheet instead of tile-effect metal roofing on a new house?

Trapezoidal steel sheet can suit a house just as well as tile-effect metal roofing if the design accounts for it. The difference does not end with appearance. Both coverings have different geometry, support and details. It is worth comparing them before installing battens and flashings. A later change may require more work than the difference in sheet price suggests. Trapezoidal sheet forms continuous lines running in the direction of the roof slope. Tile-effect metal roofing adds a transverse division that resembles rows of tiles. Flat modular versions give yet another effect than traditional waves. It is therefore worth comparing specific profiles rather than two general material names.

By |2026-11-14T10:36:53+01:002022-12-26|Knowledge base|Comments Off on What changes when you choose trapezoidal steel sheet instead of tile-effect metal roofing on a new house?

Fitting gutters: where leaks start at the eaves

Begin by establishing how water will travel from the roof edge all the way to the ground-level receiver. Match the gutter and downpipe cross-sections to the roof area draining into that section and to the outlet arrangement. Check the fall, bracket spacing and extra supports at corners and outlets. Connect the gutter to the eaves flashing while keeping joints watertight and free to move. Allow for the façade thickness so pipes and brackets do not clash with insulation.

By |2026-11-14T23:57:48+01:002022-12-24|Knowledge base|Comments Off on Fitting gutters: where leaks start at the eaves

Four things to check when choosing tile-effect metal roofing

Before comparing prices for tile-effect metal roofing, check the chosen model’s installation instructions against the slope of your roof. Then compare the sheet material and coating, the size of the sheets, and the cost of the complete order including flashings and fixings. Colour is a design choice, while suitability has to be established from the technical data. For a roof with several intersecting slopes, ask for a cutting layout to see how much sheet will be left over. Review the drawings and specifications with the designer or installer before ordering.

By |2026-11-15T03:57:40+01:002022-12-14|Knowledge base|Comments Off on Four things to check when choosing tile-effect metal roofing

Planning a loft with sloping ceilings: where will you have room to stand?

The key to a comfortable attic is matching the layout to the interior heights and the way people move around, not the floor plan alone. Before choosing furniture, check the cross-section with the slopes, beams and height at the knee walls, as well as the insulation, ventilation, light and floor load capacity. Mark out zones for everyday walking, sitting and storage, allowing for the thickness of the new insulation and lining. PIR boards can help reduce the slope thickness in a suitable arrangement, but comfort depends on the whole roof and carefully executed details.

By |2026-11-14T23:55:47+01:002022-12-13|Knowledge base|Comments Off on Planning a loft with sloping ceilings: where will you have room to stand?

What goes into a complete roof and how to estimate the cost

A complete roof comprises the structure, protective layers, covering, flashings and drainage, plus insulation and airtight junctions with partitions in a heated building. When pricing, check whether the offer covers all these elements together with installation and transport, rather than comparing the material price alone. Differences in delivery scope and parameters may not be visible at first glance, so ask for an itemised breakdown of works and materials. This helps avoid a seemingly cheap order and allows cost control.

By |2026-11-14T16:50:39+01:002022-12-10|Knowledge base|Comments Off on What goes into a complete roof and how to estimate the cost

Pricing Powerroof above-rafter insulation and roof junctions

The price of Powerroof boards is only part of the cost of over-rafter insulation. Fixings, membrane, flashings and changes at roof windows must be added to the calculation. A comparison of two variants only makes sense when it covers the same works and a similar thermal effect. Recticel Powerroof is a PIR board for over-rafter thermal insulation of pitched roofs. It has an aluminium facing and a tongue-and-groove joint on all four edges. An enquiry about PIR boards should describe the over-rafter Powerroof layer installed above the timber structure of the pitched roof slope. Powerroof must be installed above the rafters while ensuring proper fixing of the entire roof covering.

By |2026-11-16T02:21:52+01:002022-12-09|Knowledge base|Comments Off on Pricing Powerroof above-rafter insulation and roof junctions

When do the advantages of sheet metal roofing matter most?

A sheet-metal roof can be light and quick to install, yet its advantages emerge only when weighed against a specific project. Check the load-bearing capacity of the existing roof structure, the batten spacing and the fixing method, because the sheet alone does not relieve the structure without verification. For a renovation, compare the cost of preparing the substrate and the full layer build-up, not just the weight per square metre of covering. The choice of profile and sheet format should suit the roof shape and the number of details. Leave the decision to use sheet metal to the designer, who will assess pitch, loads and the required coating protection.

By |2026-11-14T16:52:19+01:002022-12-02|Knowledge base|Comments Off on When do the advantages of sheet metal roofing matter most?

Choosing an external window sill that drains rainwater away

An external sill directs water away from the façade and protects the window-to-wall junction. Tightness depends on the slope, side terminations and connection to the frame, not on the material alone. Steel sills are lightweight and easy to colour-match to roof sheeting. Aluminium, stone and other options have different installation requirements. The variant must suit the insulation and the actual width of the recess. Water from the glass and frame must not enter the gap beneath the window – the sill catches it and leads it beyond the façade face thanks to a slope and drip edge. If water seeps underneath and returns to the render, colour is irrelevant.

By |2026-11-14T23:58:03+01:002022-11-27|Knowledge base|Comments Off on Choosing an external window sill that drains rainwater away

How to calculate the cost of a roof with Thermano Roof and compare variants?

A roof with Thermano Roof is worth pricing in several variants that meet the same requirements. The difference in the price of the board is only part of the calculation. Fixing, details, work on installations and possible changes to the geometry of the covering must be calculated separately. Thermano Roof is a rigid PIR board with a gas-tight multilayer aluminium facing on both sides. The manufacturer specifies it for, among other things, flat roofs and above-rafter insulation. An enquiry about PIR boards should describe the pitched roof slope on which the insulation is to be placed above the wooden rafters. The Thermano Roof layer above the rafters must be connected with the terminations at the eaves and openings.

By |2026-11-16T02:21:35+01:002022-11-19|Knowledge base|Comments Off on How to calculate the cost of a roof with Thermano Roof and compare variants?
Back to top