+48 500 409 109

Checking roof and wall insulation against Polish requirements

Before choosing roof or wall insulation, establish which legal basis applies to your project rather than looking for a single universal U-value. Check whether the design falls under the transitional provisions as at 1 November 2026, and verify the current regulations if you order later. Compare lambda and thermal resistance R, but remember that U describes the whole building envelope, not the material alone. Assess fire, moisture, acoustics and continuity of layers too. Leave the decision on thickness and build-up to the designer.

By |2026-11-15T03:57:54+01:002026-11-01|Knowledge base|Comments Off on Checking roof and wall insulation against Polish requirements
Read More

Which Polish VAT rate applies to roofing materials and roof renovation?

In Poland, roofing materials bought on their own generally carry 23% VAT. Under the rules in force on 1 November 2026, certain work on qualifying residential property may attract the reduced rate of 8%. Eligibility depends on the contracted work, the type of building or dwelling and its usable floor area. Describing an offer as “materials and installation” does not by itself determine the rate. When comparing quotations, first check that both cover the same materials and work, then compare VAT-inclusive totals. The price of a sheet before tax tells you little about the final installed cost.

By |2026-11-14T23:58:33+01:002026-11-01|Knowledge base|Comments Off on Which Polish VAT rate applies to roofing materials and roof renovation?
Read More

How much funding is available in Poland to remove asbestos roofing?

No single subsidy amount is available to every owner of an asbestos roof, because the conditions depend on the programme and the local call. First check the rules at your municipality: what is funded, whether the aid covers dismantling, collection, transport and disposal of the waste, or only the collection of prepared material. Also establish your own contribution and ineligible costs, including the purchase of new metal roof tiles. The 2026 national call listed those works, but it was addressed to voivodeship funds with municipal participation; it was not a nationwide grant for a new roof.

By |2026-11-14T20:11:15+01:002026-11-01|Knowledge base|Comments Off on How much funding is available in Poland to remove asbestos roofing?
Read More

When is standing seam roofing a good fit for a building?

Choose a standing seam roof if you want a calm, vertical pattern across the slope, but first check whether your structure and contractor can support it. The key decision is the system: a traditionally closed seam or a ready-made snap-on panel, because a similar appearance does not mean identical tightness or behaviour under temperature changes. Before ordering, compare the complete roof with T35 or a modular metal tile, including the substrate, fixing and details. Remember that lightweight sheet metal does not prove the old roof truss is in good condition.

By |2026-11-15T03:57:36+01:002026-10-28|Knowledge base|Comments Off on When is standing seam roofing a good fit for a building?
Read More

How much do tile-effect roofing sheets cost, and how do you budget for the whole roof?

To estimate the cost of a tile-effect metal roof, start with a cutting plan and work out how much sheet metal to order. Two quotations for the same roofing can look different if one supplier includes the overlaps in the sheet area and another charges for the area actually covered. For modular sheets, work out the number of whole panels as well. Compare coating options on the same price basis and check whether VAT is included. Add separate amounts for flashings, fixings, delivery and labour to arrive at the cost of the finished roof.

By |2026-11-14T20:14:45+01:002026-10-28|Knowledge base|Comments Off on How much do tile-effect roofing sheets cost, and how do you budget for the whole roof?
Read More

How zinc-magnesium coatings protect steel roofing sheets

When choosing roof sheeting, the key is to establish whether the zinc-magnesium coating is part of a complete, well-matched system rather than the sole argument. It is worth checking where this layer sits within the sheet, what role magnesium and aluminium play, and whether cut edges can be better protected. The organic finish, workmanship and service conditions must be assessed separately. The technology name alone does not guarantee durability in every environment, so before buying, compare the parameters of the whole variant, not just the marketing slogan.

By |2026-11-15T03:58:24+01:002026-10-23|Knowledge base|Comments Off on How zinc-magnesium coatings protect steel roofing sheets
Read More

How to read a roof pitch shown in degrees or per cent

Before choosing a covering, establish whether the stated pitch is in degrees or percent — these units are not interchangeable. Check that the value applies to the specific roof slope and accounts for joints and roof penetrations. Percent describes the rise relative to horizontal distance, not the length measured along the slope. For T18 and T35 sheets and roof panels, instructions may use different units, so before requesting a quote, state the angle or pitch with its unit, the slope length and the planned details.

By |2026-11-15T03:56:31+01:002026-10-23|Knowledge base|Comments Off on How to read a roof pitch shown in degrees or per cent
Read More

What should you include in a request for quotation for an integrated photovoltaic roof?

A good quote starts with a good description of the building and expectations. If each contractor receives different information, you will get figures that cannot be fairly compared. The request should specify the roof geometry, the condition of the structure, the energy requirements and the scope of work. It is also worth asking for a description of the servicing and documentation. This ensures the discussion concerns a complete system, not just the price of the active component. Provide the location, roof drawings, cross-sections and basic dimensions. Mark windows, chimneys, roof hatches and other obstructions. If it is a renovation, add photos and information about the existing covering and any known problems. The contractor should know whether they are quoting for a new structure, a material replacement or a more complex refurbishment.

By |2026-11-15T18:59:57+01:002026-09-30|Knowledge base|Comments Off on What should you include in a request for quotation for an integrated photovoltaic roof?
Read More

How to choose roofing for an industrial hall or factory building

Start by considering what the hall is used for, since this sets the direction for choosing a covering. In an unheated building, trapezoidal sheet may be sufficient, whereas a heated one calls for sandwich panels or a build-up with structural sheet and PIR insulation. The price per metre alone should not decide. Support spacing, airtightness, acoustics and planned roof installations all count. A warehouse without heating, a workshop and a facility with a cold store each need a different covering, because temperature, water vapour, the nature of the work and aggressive substances matter.

By |2026-11-14T20:13:12+01:002026-09-05|Knowledge base|Comments Off on How to choose roofing for an industrial hall or factory building
Read More

When can second-grade 40 mm roof panels suit a new building?

A 40 mm roof sandwich panel from a cheaper batch may be tempting because of its low purchase cost, but its suitability depends on the entire roof slope. The thermal conditions inside, the loads, the geometry and the reason for the price reduction all need to be assessed. In a new building, it is better to carry out these checks before ordering the steel. Only then does the panel price become part of a meaningful comparison of options. An unheated storage facility and an all-year workplace have different requirements. A thickness of 40 mm alone does not confirm that the roof will provide the required insulation performance. Panel data and an assessment of the building envelope for the specific conditions are needed. Also consider the planned use, not just the first months after construction.

By |2026-11-14T16:50:00+01:002026-08-28|Knowledge base|Comments Off on When can second-grade 40 mm roof panels suit a new building?
Read More
Back to top