Knowledge base2026-11-15T18:56:00+01:00

Choose a product group

Metal roofing

Sandwich panels

PIR insulation boards

XPS

Accessories

Fencing

Knowledge base

Izoprofil.com helps you compare materials for a specific building project. The guides cover the uses of sandwich panels, PIR insulation boards, metal roof tiles and trapezoidal sheets. The criteria depend on the application, including the supporting structure, thermal performance and requirements for the finished surface. Read the product specifications, identify which dimensions affect the order and compare complete solutions. The articles help you discuss the options with a designer or installer and check the suitability of the selected materials before purchase.

PIR, EPS, XPS or mineral wool: choosing insulation for the roof build-up

Start by establishing where the heated part of the building ends, not by comparing material coefficients. If the loft is unheated, insulate the partition above the rooms; if it is used, insulate the roof slope together with its wall junctions. Only then compare PIR, EPS, XPS and mineral wool at the required thermal resistance and permitted layer arrangement, taking account of support, moisture, fire and loads. PIR delivers high resistance at low thickness, wool suits fire and acoustic requirements, EPS can be economical, and XPS is chosen where resistance to moisture and compression is needed. No material replaces airtightness, waterproofing and correct details.

How chimney flashings keep rain out

A chimney flashing has to lead water from the roof slope around the chimney and direct it back onto the covering. Its effectiveness depends on matching the sheet profile, the roof pitch and the chimney’s dimensions. The rear section, the sides and the junction with the chimney wall are crucial. Sealant plays only a supporting role – it cannot replace properly shaped sheet metal or the freedom of materials to move. During renovation, the underlay should also be checked. A chimney interrupts the continuity of the slope, and water has to get past this obstacle. The roof and chimney may move differently due to temperature or structural movement.

Choosing a ridge cap to suit the shape of the roof and building

The ridge closes off the roof silhouette. Seen from ground level, it may appear as a thin line or as a distinct element above the roof slopes. Ridge caps therefore influence how the building is perceived, even though their primary function remains technical. They cover a specific zone where the slopes meet. The choice of shape should satisfy both requirements. A handsome detail makes sense when it suits the covering, the seals and the method of fixing. On a simple building form with a large roof slope, a small difference in the height of the ridge cap can distinctly change the roof line. With a complex arrangement of slopes, the ridge is just one of many details. It is therefore worth assessing it in the view of the whole building. A close-up of the product alone does not show its effect on proportions.

Galvanised sections and building maintenance costs: what to establish before purchase

The cost of the profiles does not end on the day of delivery. Maintenance of the structure over the following years also matters. Galvanised profiles can reduce the scope of protective work in a suitably selected application. However, it is worth establishing the conditions of use, access for inspection and how damage is to be handled. Z-sections, channels, sigma and omega profiles have different places in the building, and with them different contact with moisture and contaminants. The term 'enclosed hall' does not yet say everything about the conditions of the steel. A dry warehouse differs from a room with a wet process or high humidity. Condensation, the supply of fresh air and the type of contaminants are important. It is worth describing these factors before selecting the coating. This allows later surprises to be avoided in a place that is formally under a roof.

Keeping loft insulation continuous at walls, windows and service penetrations

The most demanding parts of a loft insulation job are the roof-to-wall junctions, window frames and service penetrations. At each one, the insulation needs to continue without a gap and the layer on the room side needs an airtight seal. Before choosing a material, check the condition of the roof, how moisture can escape and how much headroom you can spare. Mineral wool between the rafters and PIR boards above them occupy different positions in the roof. Draw the junctions to see where a further layer is needed. Inspect them with the installer while they are still accessible, before the lining goes on.

Clay roof tiles or tile-effect steel for a house?

The choice of covering depends primarily on the roof structure, the geometry of the slopes, the comfort of the attic and the cost of the complete set, not on the material name alone. Check whether the design accounts for the weight of the chosen solution and whether the supports and connections are suited to its installation. In an existing building, changing the covering requires an assessment of load-bearing capacity, not just a look at the rafters. Compare complete systems with the substrate, accessories and flashings, as only these reveal the real differences.

Back to top