What to consider when fitting square gutters to a metal roof

Square gutters stand out for their clean eaves line and fit with many contemporary buildings, yet they do not automatically offer greater capacity. On a metal roof, check above all the system dimensions, the effective roof area, the positioning of outlets, and whether the eaves flashing matches the roof pitch and overhang. Aesthetics depend on the eaves proportions, building size and downpipe routing, so judge appearance together with function. Remember fixings, thermal movement and cleaning, and base the hydraulic selection on the system data and roof layout.

By |2026-11-14T16:52:04+01:002022-09-17|Knowledge base|Comments Off on What to consider when fitting square gutters to a metal roof

What determines the service life of tile-effect metal roofing?

The durability of a metal roof tile depends above all on matching the coating and core thickness to the conditions on the roof, and on correct installation of the entire covering. Rather than looking for one universal number of years, it is worth checking the specific product: the type of metallic and organic coating, its suitability for the given environment, and maintenance requirements. Edges, fasteners, ventilation beneath the covering and the condition of flashings also matter. The number of warranty years is not the same as expected service life. A roof near a forest, industrial plant or coast operates in a different environment from one in quiet, open housing.

By |2026-11-14T16:51:29+01:002022-09-08|Knowledge base|Comments Off on What determines the service life of tile-effect metal roofing?

How do you convert the thickness of EPS to PIR for the same wall?

PIR can provide a similar thermal resistance in a thinner layer than a selected EPS, but there is no single conversion factor for all boards. You need to compare the lambda of specific types and their application. Only then can you assess how much space can be recovered and how the change will affect the render, reveals and other wall layers. Lambda describes heat conduction through a material. The lower it is, the greater the resistance of a layer of the same thickness. In a simple calculation, the resistance R is d divided by lambda, where d is given in metres. U, on the other hand, relates to the entire building element and requires the other layers and the calculation conditions to be taken into account.

By |2026-11-14T10:38:35+01:002022-09-04|Knowledge base|Comments Off on How do you convert the thickness of EPS to PIR for the same wall?

Where to place a rainwater gully so you can clear it later

A gutter sediment trap is installed as an accessible point between the downpipe and the underground pipe to make inspection and cleaning easier. Before installation, check where the water drains and whether it can back up, and match the product to the pipe diameter, outlet level and installation location. Ensure a stable base, tight connections and free access to the basket. Remember that the trap does not replace gutter cleaning or solve a blocked installation. How it works depends on the product design, so leave the choice of solution to the designer.

By |2026-11-14T23:57:49+01:002022-08-24|Knowledge base|Comments Off on Where to place a rainwater gully so you can clear it later

Laying modular tile-effect roofing from the eaves to the cuts at a roof valley

Before ordering the battens, establish the exact model and variant of the modular metal roof tile, as this determines the batten spacing and fixing method. Check the instructions for the permitted pitch, sheet geometry, laying sequence and connection rules. A similar appearance of two modules does not guarantee identical installation, especially at ends and corners. The documentation should be on site before the support is built. Choose the specific roofing variant and only then plan the work, to avoid corrections and uncertainty at every joint.

By |2026-11-15T03:58:12+01:002022-08-22|Knowledge base|Comments Off on Laying modular tile-effect roofing from the eaves to the cuts at a roof valley

Why does the north wall need particular attention when designing insulation?

The north façade usually receives less direct sunlight, so its drying may proceed differently than on the south side. Inside the building, however, the risk of moisture is also determined by surface temperature, thermal bridges and air exchange. Well-planned insulation combines thermal protection with water drainage and vapour control. A wet façade surface may result from rain, water splashing back from the ground or faulty rainwater drainage. Moisture at an internal corner may have a different source: a cold surface and vapour from the room. When assessing the problem, the two situations should not be lumped together under the single label 'the wall doesn't breathe'.

By |2026-11-14T10:38:23+01:002022-08-06|Knowledge base|Comments Off on Why does the north wall need particular attention when designing insulation?

How do you choose a mineral wool wall panel for several different jobs?

The best mineral wool panel is one that matches the job of a specific wall and fits the rest of the project. A new hall may have a warm office, a noisy workshop and a cool warehouse. A single parameter will not describe all these zones. It is worth starting the choice with function, and only then moving on to thickness, the joint and the colour of the facing. On one plan, mark the heated rooms, areas of increased humidity, noise sources and the routes of partitions requiring fire resistance. Add the position of gates and windows. Such a map allows you to check whether the selected panel is to perform one job or several at once.

By |2026-11-14T10:37:17+01:002022-07-25|Knowledge base|Comments Off on How do you choose a mineral wool wall panel for several different jobs?

When to choose tile-effect roofing sheets cut to length

Blachodachówka cut to size is a solution worth considering when the roof geometry helps reduce transverse overlaps. Before ordering, however, check not only the sheet format but above all the entire roof slope layout, the positions of valleys and dormers, and the transport and installation conditions. A detailed schedule of sheets with their lengths and laying direction is key, not just the area in square metres. Leave the final choice between cut-to-size blachodachówka and modules to the designer, as the fit to the specific roof is what matters.

By |2026-11-14T20:13:23+01:002022-07-23|Knowledge base|Comments Off on When to choose tile-effect roofing sheets cut to length

Metal fence pickets, rails and fixings from different suppliers: how do you check that the set is compatible?

Assembling a metal picket fence from several offers requires checking whether the selected parts can actually work together. A similar colour and a matching screw length do not confirm that the whole set is compatible. You need to take into account the geometry of the picket, the support, the material of the rails and the permitted method of fixing. On Izoprofil.com we describe how to check such a purchase before approving orders. The guide covers samples, connection drawings, separating deliveries and later identification of parts. It does not establish a universal spacing of supports or number of connectors. These data must follow from the specific solution and the conditions of the fence. Clarifying compatibility early makes it easier to distinguish a real saving from a set that, after delivery, requires new components or a change to the previously planned installation.

By |2026-11-15T18:59:55+01:002022-07-16|Knowledge base|Comments Off on Metal fence pickets, rails and fixings from different suppliers: how do you check that the set is compatible?

Arched or stepped fences: ordering pickets for a changing top line

A picket fence does not have to end in a single straight line. Different lengths allow a stepped layout or a gently changing height. However, the intention must be described precisely. Metal pickets should not be ordered on the basis of the phrase 'on a curve' alone. It can mean different things. First a drawing is needed, and only then a list of dimensions for production. A curve in the top line can be achieved by setting straight pickets of different lengths. This is a different task from physically bending each element. It should not be assumed that a sheet metal profile may be bent freely on site. The shape and method of processing must correspond to the product documentation.

By |2026-11-15T18:59:23+01:002022-07-16|Knowledge base|Comments Off on Arched or stepped fences: ordering pickets for a changing top line
Back to top