Writing a brief for a new steel building on an operating site

A new steel hall should solve the company's problems that can be named. Lacking space to receive deliveries? Machines standing too close together? Goods waiting outside? Such questions are a good starting point for the design brief. The instruction to build a larger building alone provides too little information. A description of the work, the constraints and the expected change is needed. The owner knows the development plan, the warehouse operative knows the daily bottlenecks, and the maintenance department knows the servicing problems. Each of these perspectives can change the layout of the steel hall. It is worth gathering them before approving the dimensions. An error on a sketch is easier to correct than a column standing where a large part of a machine needs to be replaced.

By |2026-11-15T03:58:27+01:002023-10-05|Knowledge base|Comments Off on Writing a brief for a new steel building on an operating site

Standing seam or trapezoidal cladding for a metal façade?

When choosing a standing seam metal façade, first establish whether the product is intended for walls rather than only for roofs. Check the fixing method, the substructure and the ventilation of the entire cladding. Plan the panel layout on a drawing before ordering lengths and flashings, linking the rhythm to window widths and the building's articulation. When comparing with trapezoidal sheet, do not rely on the profile name alone: verify the cover width, steel thickness and wall variant. Leave design decisions to the designer.

By |2026-11-14T23:55:45+01:002023-10-01|Knowledge base|Comments Off on Standing seam or trapezoidal cladding for a metal façade?

What makes standing seam roofing panels easier to install?

Whether installing snap-lock seam panels will be straightforward depends above all on the system matching the actual substrate and roof geometry, not on the factory-formed seam alone. Check that the substrate is level and stable, that thermal movement of the metal is allowed for, and that details at the eaves, ridge and penetrations are complete. Snap-lock panels and traditional standing seam are different solutions, so instructions, minimum pitches and accessories should not be transferred between them without confirming compatibility. The simple appearance of the covering demands high accuracy, because unevenness is easily revealed in the light.

By |2026-11-14T16:52:21+01:002023-09-30|Knowledge base|Comments Off on What makes standing seam roofing panels easier to install?

Hipped roofs on a rectangular plan: how the four slopes fit together

A hipped roof encloses the building with four slopes: two trapezoidal and two triangular. This arrangement suits a simple building form well, yet it multiplies the corners and covering cut-offs. The designer matches the truss to the span and loads. When choosing metal roof tiles, establish the covering area, the waste at corners and the full set of flashings – the footprint area alone will not suffice for ordering material. On a rectangular building, the larger slopes meet at the ridge, while the shorter sides are closed by triangular slopes. Their convex junctions are corners, not valleys.

By |2026-11-14T23:57:15+01:002023-09-29|Knowledge base|Comments Off on Hipped roofs on a rectangular plan: how the four slopes fit together

Planning a roof covering replacement step by step

Begin by checking what actually needs replacing, not by choosing the new material. Inspect the covering, flashings, gutters, substructure and visible parts of the roof trusses, looking for leak causes and signs of persistent moisture. Assess whether the wear is local or affects the entire roof slope, as this shapes the scope of work. Only then compare coverings using real dimensions, set the schedule, protect the building, check the substrate, lay the new layers and hand over the roof with documentation.

By |2026-11-14T20:14:01+01:002023-09-24|Knowledge base|Comments Off on Planning a roof covering replacement step by step

PIR, EPS, XPS or mineral wool: choosing insulation for the roof build-up

Start by establishing where the heated part of the building ends, not by comparing material coefficients. If the loft is unheated, insulate the partition above the rooms; if it is used, insulate the roof slope together with its wall junctions. Only then compare PIR, EPS, XPS and mineral wool at the required thermal resistance and permitted layer arrangement, taking account of support, moisture, fire and loads. PIR delivers high resistance at low thickness, wool suits fire and acoustic requirements, EPS can be economical, and XPS is chosen where resistance to moisture and compression is needed. No material replaces airtightness, waterproofing and correct details.

By |2026-11-14T23:58:35+01:002023-09-22|Knowledge base|Comments Off on PIR, EPS, XPS or mineral wool: choosing insulation for the roof build-up

How chimney flashings keep rain out

A chimney flashing has to lead water from the roof slope around the chimney and direct it back onto the covering. Its effectiveness depends on matching the sheet profile, the roof pitch and the chimney’s dimensions. The rear section, the sides and the junction with the chimney wall are crucial. Sealant plays only a supporting role – it cannot replace properly shaped sheet metal or the freedom of materials to move. During renovation, the underlay should also be checked. A chimney interrupts the continuity of the slope, and water has to get past this obstacle. The roof and chimney may move differently due to temperature or structural movement.

By |2026-11-14T23:56:49+01:002023-09-07|Knowledge base|Comments Off on How chimney flashings keep rain out

Choosing a ridge cap to suit the shape of the roof and building

The ridge closes off the roof silhouette. Seen from ground level, it may appear as a thin line or as a distinct element above the roof slopes. Ridge caps therefore influence how the building is perceived, even though their primary function remains technical. They cover a specific zone where the slopes meet. The choice of shape should satisfy both requirements. A handsome detail makes sense when it suits the covering, the seals and the method of fixing. On a simple building form with a large roof slope, a small difference in the height of the ridge cap can distinctly change the roof line. With a complex arrangement of slopes, the ridge is just one of many details. It is therefore worth assessing it in the view of the whole building. A close-up of the product alone does not show its effect on proportions.

By |2026-11-15T03:58:59+01:002023-09-03|Knowledge base|Comments Off on Choosing a ridge cap to suit the shape of the roof and building

Galvanised sections and building maintenance costs: what to establish before purchase

The cost of the profiles does not end on the day of delivery. Maintenance of the structure over the following years also matters. Galvanised profiles can reduce the scope of protective work in a suitably selected application. However, it is worth establishing the conditions of use, access for inspection and how damage is to be handled. Z-sections, channels, sigma and omega profiles have different places in the building, and with them different contact with moisture and contaminants. The term 'enclosed hall' does not yet say everything about the conditions of the steel. A dry warehouse differs from a room with a wet process or high humidity. Condensation, the supply of fresh air and the type of contaminants are important. It is worth describing these factors before selecting the coating. This allows later surprises to be avoided in a place that is formally under a roof.

By |2026-11-15T18:56:28+01:002023-08-28|Knowledge base|Comments Off on Galvanised sections and building maintenance costs: what to establish before purchase

Keeping loft insulation continuous at walls, windows and service penetrations

The most demanding parts of a loft insulation job are the roof-to-wall junctions, window frames and service penetrations. At each one, the insulation needs to continue without a gap and the layer on the room side needs an airtight seal. Before choosing a material, check the condition of the roof, how moisture can escape and how much headroom you can spare. Mineral wool between the rafters and PIR boards above them occupy different positions in the roof. Draw the junctions to see where a further layer is needed. Inspect them with the installer while they are still accessible, before the lining goes on.

By |2026-11-15T03:58:14+01:002023-08-19|Knowledge base|Comments Off on Keeping loft insulation continuous at walls, windows and service penetrations
Back to top