Planning a steel production building around people and material flow

A short material route can matter more than a few extra metres of steel hall. If raw material circulates between stations and people cross the forklift route, a larger building will not eliminate the problem. It is worth drawing the production layout before determining the column grid and gate locations. The structure should create the conditions for the process that is to operate within it. Start with the sequence of operations. Identify raw material intake, preparation, processing, inspection, packaging and dispatch. Not every company needs all these zones, but every company should know its own workflow. A steel hall should enable movement between them without unnecessary backtracking and blocking of other tasks.

By |2026-11-15T03:58:29+01:002023-10-28|Knowledge base|Comments Off on Planning a steel production building around people and material flow

When does T35 offer an advantage over T18 in a new building?

On a roof slope 7.6 m wide, the selected T18 and T35 variants require a different number of runs. This is one of the reasons why a taller trapezoidal profile should not be chosen by name alone. The article compares specific dimensions, the cutting layout and the support conditions. It also shows what changes in the details and how to assess the cost of both solutions before construction. In the examples considered here, the trapezoidal height is 18 and 35 mm respectively. The other dimensions, however, do not follow from the symbol alone. Profiles with a similar name may differ in the width of the crests, valleys and the entire sheet. A cross-section drawing is therefore needed both to verify load capacity and to plan the quantity of material.

By |2026-11-14T16:50:19+01:002023-10-27|Knowledge base|Comments Off on When does T35 offer an advantage over T18 in a new building?

Where Z-purlins can save money on a steel building roof

Z-purlins are a popular element of steel roofs. Their advantage lies in the possibility of building orderly purlin layouts from parts prepared for assembly. This can bring material and organisational savings. However, these do not follow from the name of the section alone. Cold-formed profiles must be selected for loads, frame spacing and cladding. Only then can it be assessed which solution will be beneficial for the investor. The spacing of the main frames affects the span length of the purlins. The purlin spacing, in turn, affects the load on each of them and the performance of the covering. These decisions are interrelated. Reducing the number of profiles may increase the requirements placed on the remaining elements. Optimisation should therefore cover the roof as a whole. It is not enough to remove a few lines of support from the drawing.

By |2026-11-15T03:59:30+01:002023-10-18|Knowledge base|Comments Off on Where Z-purlins can save money on a steel building roof

Writing a brief for a new steel building on an operating site

A new steel hall should solve the company's problems that can be named. Lacking space to receive deliveries? Machines standing too close together? Goods waiting outside? Such questions are a good starting point for the design brief. The instruction to build a larger building alone provides too little information. A description of the work, the constraints and the expected change is needed. The owner knows the development plan, the warehouse operative knows the daily bottlenecks, and the maintenance department knows the servicing problems. Each of these perspectives can change the layout of the steel hall. It is worth gathering them before approving the dimensions. An error on a sketch is easier to correct than a column standing where a large part of a machine needs to be replaced.

By |2026-11-15T03:58:27+01:002023-10-05|Knowledge base|Comments Off on Writing a brief for a new steel building on an operating site

Standing seam or trapezoidal cladding for a metal façade?

When choosing a standing seam metal façade, first establish whether the product is intended for walls rather than only for roofs. Check the fixing method, the substructure and the ventilation of the entire cladding. Plan the panel layout on a drawing before ordering lengths and flashings, linking the rhythm to window widths and the building's articulation. When comparing with trapezoidal sheet, do not rely on the profile name alone: verify the cover width, steel thickness and wall variant. Leave design decisions to the designer.

By |2026-11-14T23:55:45+01:002023-10-01|Knowledge base|Comments Off on Standing seam or trapezoidal cladding for a metal façade?

What makes standing seam roofing panels easier to install?

Whether installing snap-lock seam panels will be straightforward depends above all on the system matching the actual substrate and roof geometry, not on the factory-formed seam alone. Check that the substrate is level and stable, that thermal movement of the metal is allowed for, and that details at the eaves, ridge and penetrations are complete. Snap-lock panels and traditional standing seam are different solutions, so instructions, minimum pitches and accessories should not be transferred between them without confirming compatibility. The simple appearance of the covering demands high accuracy, because unevenness is easily revealed in the light.

By |2026-11-14T16:52:21+01:002023-09-30|Knowledge base|Comments Off on What makes standing seam roofing panels easier to install?

Hipped roofs on a rectangular plan: how the four slopes fit together

A hipped roof encloses the building with four slopes: two trapezoidal and two triangular. This arrangement suits a simple building form well, yet it multiplies the corners and covering cut-offs. The designer matches the truss to the span and loads. When choosing metal roof tiles, establish the covering area, the waste at corners and the full set of flashings – the footprint area alone will not suffice for ordering material. On a rectangular building, the larger slopes meet at the ridge, while the shorter sides are closed by triangular slopes. Their convex junctions are corners, not valleys.

By |2026-11-14T23:57:15+01:002023-09-29|Knowledge base|Comments Off on Hipped roofs on a rectangular plan: how the four slopes fit together

Planning a roof covering replacement step by step

Begin by checking what actually needs replacing, not by choosing the new material. Inspect the covering, flashings, gutters, substructure and visible parts of the roof trusses, looking for leak causes and signs of persistent moisture. Assess whether the wear is local or affects the entire roof slope, as this shapes the scope of work. Only then compare coverings using real dimensions, set the schedule, protect the building, check the substrate, lay the new layers and hand over the roof with documentation.

By |2026-11-14T20:14:01+01:002023-09-24|Knowledge base|Comments Off on Planning a roof covering replacement step by step

PIR, EPS, XPS or mineral wool: choosing insulation for the roof build-up

Start by establishing where the heated part of the building ends, not by comparing material coefficients. If the loft is unheated, insulate the partition above the rooms; if it is used, insulate the roof slope together with its wall junctions. Only then compare PIR, EPS, XPS and mineral wool at the required thermal resistance and permitted layer arrangement, taking account of support, moisture, fire and loads. PIR delivers high resistance at low thickness, wool suits fire and acoustic requirements, EPS can be economical, and XPS is chosen where resistance to moisture and compression is needed. No material replaces airtightness, waterproofing and correct details.

By |2026-11-14T23:58:35+01:002023-09-22|Knowledge base|Comments Off on PIR, EPS, XPS or mineral wool: choosing insulation for the roof build-up

How chimney flashings keep rain out

A chimney flashing has to lead water from the roof slope around the chimney and direct it back onto the covering. Its effectiveness depends on matching the sheet profile, the roof pitch and the chimney’s dimensions. The rear section, the sides and the junction with the chimney wall are crucial. Sealant plays only a supporting role – it cannot replace properly shaped sheet metal or the freedom of materials to move. During renovation, the underlay should also be checked. A chimney interrupts the continuity of the slope, and water has to get past this obstacle. The roof and chimney may move differently due to temperature or structural movement.

By |2026-11-14T23:56:49+01:002023-09-07|Knowledge base|Comments Off on How chimney flashings keep rain out
Back to top