Planning a roof replacement: what to check and in what order

Begin by inspecting the trusses, supports and connections to find out where the leak originates. The cause may lie in the material itself or in a detail at the chimney, valley or eaves – in which case new sheets alone will not suffice. Only after this assessment should you choose the sheet metal, underlay and flashings, bearing in mind that T18, T35 and tile-profile sheeting reduce weight but will not strengthen a damaged structure. Plan the measurements, rain protection and inspection of each layer, and settle insulation, drainage and roof equipment straight away.

By |2026-11-14T23:58:37+01:002024-11-11|Knowledge base|Comments Off on Planning a roof replacement: what to check and in what order

Choosing a roof underlay membrane: which specifications matter?

A roof membrane is selected primarily according to the layer build-up and the type of covering, not by grammage alone. It is worth checking the product's intended use, the tightness of joints and the permitted exposure time. The underlay membrane on the outer side drains water from beneath the covering, while the inner layer limits the passage of moist air and vapour in line with the design. These are different tasks and working conditions, so casually calling both of them foil leads to mistakes. The selection decision is left to the designer, who assesses the entire build-up.

By |2026-11-14T23:58:18+01:002024-11-11|Knowledge base|Comments Off on Choosing a roof underlay membrane: which specifications matter?

When is tile-effect metal roofing worth the cost?

Buying a metal roof tile can still be worthwhile if the covering suits the roof geometry and structure. Rather than being guided by a promotion per metre, ask for a laying plan for both the cut-to-length and modular versions, then compare the quantity of material, the coverage area and the offcuts. Also check whether the offer includes flashings, fixings and transport, and what parameters the core and coating have. The final decision rests with the designer, as not every model suits every pitch.

By |2026-11-14T16:52:03+01:002024-11-06|Knowledge base|Comments Off on When is tile-effect metal roofing worth the cost?

How profile, coating and roof build-up work together on a trapezoidal steel roof

Trapezoidal steel sheet is one component of the roof. The profile and thickness must be matched to the loads, and the coating to the environment. The remaining layers depend on how the building is used. It is worth defining them together before the supports are built. This allows the eaves, ridge, insulation and fixings to form a coherent solution without corrections during installation. Start with the temperature and humidity you expect in the rooms. An open canopy performs differently from a heated hall, and differently again from a place where a technical process releases a lot of steam. The name “utility building” alone says little about these conditions. The actual pattern of use must be described.

By |2026-11-14T16:50:02+01:002024-11-01|Knowledge base|Comments Off on How profile, coating and roof build-up work together on a trapezoidal steel roof

What can replace an old asbestos-cement roof?

Before laying a new covering, check whether the old asbestos-cement really contains asbestos – not every fibre-cement sheet does. If asbestos is confirmed or even suspected, do not break, cut or remove the sheets yourself; leave the removal to a company equipped for such work, which should also take away the waste. Only then prepare the new roof layers and order the material, choosing from trapezoidal sheet metal, modular metal tiles or an insulated roof panel. The decision depends on the structure’s condition, the roof pitch and how the building is used.

By |2026-11-14T20:13:26+01:002024-10-19|Knowledge base|Comments Off on What can replace an old asbestos-cement roof?

How many sandwich panel fixings does your support layout require?

It is worth replacing the question of the number of screws per metre with the question of the number of fixings in each field of the wall or roof. Loads are not distributed evenly everywhere, and different fasteners have different tasks. In a new building, the schedule is produced from the support plan, wind zones and the specific panel. Only then can the average purchase quantity be calculated. A square metre of panel, a linear metre of its length and a metre of flashing are different units. If the question does not specify the basis, a numerical answer can be misleading. Equally important is the distinction between structural fixing screws and fasteners for thin finishing elements.

By |2026-11-14T12:53:59+01:002024-10-19|Knowledge base|Comments Off on How many sandwich panel fixings does your support layout require?

Five practical benefits of exterior steel window sills

Whether a steel external window sill works depends above all on proper drainage of water away from the wall, not on the lightness of the sheet alone. When choosing one, check the slope, drip edge, side ends and the tightness of the connection to the window, because these details determine effectiveness. The light material is easily deformed, so it needs stable support and fixing suited to the window and façade. Measurement should account for the finished façade, space for side ends and the junction with reveals. Assess these elements together with colour and cost.

By |2026-11-14T20:13:28+01:002024-10-18|Knowledge base|Comments Off on Five practical benefits of exterior steel window sills

How does roof shape help you choose modular or made-to-measure tile-effect metal roofing?

The format of tile-effect metal roofing should be matched to the roof geometry and the organisation of works. A long sheet can be convenient on a rectangular slope. Smaller modules give greater freedom with hips and difficult access. No format guarantees the lowest price or zero waste. The answer is given by the layout of elements on the actual dimensions of the structure. A made-to-measure sheet is produced to a specified length within the limits of the given system. Its width and the rhythm of the profiles remain fixed. This does not mean that any rectangle can be ordered without taking cut locations into account. With a longer strip, the termination at the eaves and ridge must also be determined.

By |2026-11-14T10:36:44+01:002024-10-16|Knowledge base|Comments Off on How does roof shape help you choose modular or made-to-measure tile-effect metal roofing?

Which insulated roof panel lengths are actually in stock?

Production length and off-the-shelf availability are two different pieces of information. The catalogue shows what a given system can offer, while a specific batch has its own set of dimensions, colour and coatings. Before choosing roof sheets, compare the required lengths with the confirmed list of pieces. A change of format can affect laps, support, transport and installation cost. The length range stated for a product does not mean that every format is waiting in stock. Made-to-measure production may require a separate lead time, and ready batches often come in limited quantities. Availability information should be linked to the confirmation date and the exact specification, not just the core name.

By |2026-11-14T16:49:10+01:002024-10-10|Knowledge base|Comments Off on Which insulated roof panel lengths are actually in stock?

Safe access to the roof and safe routes across it

Many roof defects are visible from the ground or from inside the loft. A displaced flashing, an overflowing gutter or a water stain can be photographed from a safe position. Those photographs help a roofer decide where a closer inspection is needed. For access to a chimney or a piece of equipment, the whole route from the roof entry point to the work area matters. A professional can assess the supports and the condition of the covering, select fall protection and check the positions of roof steps or walkways. Rain affects grip on sheet metal. A ladder and grippy footwear alone do not provide adequate protection.

By |2026-11-15T03:56:29+01:002024-10-09|Knowledge base|Comments Off on Safe access to the roof and safe routes across it
Back to top