Choose a material

Roofing sheets

Sandwich panels

PIR insulation boards

XPS

Accessories

Fencing

PIR insulation boards

EFIGREEN ALU+ or ALU+ XL: board format and installation cost

At a glance

Comparing EFIGREEN ALU+ and ALU+ XL requires laying out both formats on the same roof slope. A larger board may reduce the number of full elements, but with numerous service penetrations it does not necessarily reduce waste or labour. The price should cover cuts, the use of the remaining offcuts and transport of the boards to the installation location. Attach to your enquiry the layout of the base mounts, the widths of narrow strips and the lengths of the available fields. Check the exact variant, thickness and edges in the delivery documentation, because the family name alone is not enough to determine the coverage. Below, we separate the thermal properties from the cost of cutting and show what to confirm before choosing a format.

Ochre face and pale board section, illustration for the EFIGREEN ALU+ guide — Izoprofil.com

The subject of purchase must be unambiguous

The relevant thermal parameter must be compared with the board cutting plan, not just with the price per square metre. Any doubts concerning the joints are clarified by the specialist preparing the cutting plan and the delivery schedule before the quotes are compared by final amount.

The correct product and the scope of its data

In the EFIGREEN ALU+ specification, the full name, thickness and format must be given, because the abbreviation “polyurethane boards” alone does not identify the product. The core is made of PIR, and the composite facing combines kraft paper, aluminium and PE film; the properties of the complete board therefore relate to the entire layer system, not just the foam. Lambda is 0.023 W/(m·K) for 30–35 mm and 0.022 W/(m·K) in the stated range of 40–160 mm, the data sheet states CS(10/Y)200, and the Polish page designates the reaction to fire as NPD, i.e. no declared performance for that property. The basic format is 600 × 600 mm, whereas ALU+ XL comes in other dimensions depending on the variant.

A uniform basis for calculation

For the basic EFIGREEN ALU+ format, a 600 × 600 mm sheet has an area of 0.36 m², so 60 full sheets give 21.60 m² before cutting — this is not the number of pieces in a factory pack. The XL variant requires a separate calculation for its actual dimensions, because a larger sheet area does not determine the usefulness of the offcuts; the result is determined by the share of short offcuts around obstacles. A cutting plan drawing for the specific ALU+ or XL format allows both offers to be compared on the same basis.

In EFIGREEN ALU+, lambda depends on thickness, so the unit of comparison must be based on the variant actually selected for the building. In architecture with numerous obstacles, the share of short offcuts changes sheet consumption, so it is worth calculating the cutting plan for the openings before pricing. A cutting plan drawing for the ALU+ or XL format shows what the assumption relates to, and the measurement with separately listed waste completes the scope of delivery.

What drives the cost of the solution

Laying the basic 600 × 600 mm format and the XL variant are different scopes of work, especially in the narrow field between two installation bases. With EFIGREEN ALU+, the lambda specified for the thicker board cannot be attributed to the thinner board, because the comparison would then cover different assumptions. The cutting plan and the delivery schedule should be confirmed by a specialist before the choice of the more financially advantageous item can be justified.

Labour hidden in the joints

The surface of EFIGREEN ALU+ is formed by a factory-applied facing; its compatibility with the adhesive, fixing and covering is checked for the ordered variant. In the case of tight transitions between installation bases, price the preparation of cut pieces and the protection of the joints. The acceptance documentation should identify the supplied variant and the completed terminations before they are covered.

Transport, offcuts and preparation

With EFIGREEN ALU+, the quotation must cover not only the delivery of material but also the preparation of a stable substrate for small fragments in the area of penetrations and the determination of who carries out these works. The number of boards is determined by the measurement for the selected format with separately shown waste, and if the proportion of short cut pieces around obstacles changes, the requirement must be verified. The agreed covering and method of fixing affect the schedule, because waiting can increase the cost of protection. Only a full scope calculated in this way combines the correct thermal parameter with a sensible cutting plan.

Conditions for accepting the final quote

The order for EFIGREEN ALU+ must correspond to the cutting plan drawing for the specific ALU+ or XL format, and acceptance should indicate the full name of the variant, the thickness and the delivery format. This ensures that the documents do not describe a different variant from the one supplied. It is also worth establishing the settlement of changes in the narrow field between two installation bases and checking the completeness of the scope before signing it. If a substitution is proposed, the sheet consumption must be recalculated after the arrangement of the openings, so that the thermal insulation of the roof slope with numerous installation penetrations remains consistent with the objective.

7 branches. Materials closer to your project.

Izoprofil.com map of seven branches offering sandwich panels, PIR boards and sheet metal
  • SEROCK — Dzierżenin 34 E [mapa]
  • BŁONIE — ul. Sochaczewska 138A [mapa]
  • RADOM — ul. Grobickiego 8 [mapa]
  • ŁÓDŹ — Natolin 8 [mapa]
  • OLSZTYN — Barczewo, ul. Prosta 9 [mapa]
  • WROCŁAW — ul. Jerzmanowska 10C [mapa]
  • GORZÓW WLKP. — ul. Zielona 33/34 [mapa]

Check prices and availability: +48 500 409 109

Free quote

Materials for your project