PIR insulation
Buying swissporPIR Alu: covering area and edge profiles
When buying swissporPIR Alu, thickness alone is not enough to compare offers, because the same product comes with three edge types: FIT/GK is a square edge, LAP/SF is a rebated edge, and TAG/NuF is tongue and groove. The request for quotation should specify the exact designation, not a general “polyurethane boards” or “polyurethane foam”. The purchase cost must include cut-offs and edge finishing, because profiling the edges does not eliminate all work on site. When comparing prices, assign the correct shapes to the FIT/GK, LAP/SF and TAG/NuF designations so that the offers relate to the same variant.

PIR boards with FIT, LAP or TAG edge
A short name from the price list does not determine how adjacent boards are to be fitted together, because similarly named profiles can behave differently. The choice of edge is meant to allow ordering a geometry consistent with the laying plan and the terminations. Pass on to all tenderers a verbal description of the edge together with a drawing of the actual cross-section, so that the prices relate to a comparable task.
Core conductivity and quality of contact
Assess the surcharge for the swissporPIR Alu profile by the execution of the joints, not by a change in the conductivity of the core. Its declaration remains at 0.022 W/(m·K), regardless of the name of the edge. In the tender comparison, therefore, separate the thermal parameter of the board from the function of the selected edge.
Before comparing amounts, separate the core conductivity of swissporPIR Alu from the quality of execution of the joints. A cheaper item may produce a different effect, since the edge profile does not automatically improve the lambda value and does not eliminate the influence of the other thermal bridges. Assess the benefit of the profile as an aid in maintaining the continuity of the layer. In the tender table, include the thermal properties of the board and the joint plan over the entire surface, and link the price difference to a specific change in parameters.
Polyurethane insulation after trimming the edges
The factory edge profile of swissporPIR Alu must be clean and undamaged, and the boards fitted without gaps. When a board is cut to size, this profile is removed, so the quantity survey should include the cut edge at the wall or at a projecting roof element.
After cutting off the factory profile, the correct end of the swissporPIR Alu board must be recreated. Calculating just the rectangular area can be misleading, because a loose tongue does not replace proper support for the edge section. The cutting plan must fit the perimeter without open joints and unstable parts, and the quotation must include the edge condition, the width of the cut piece and how it is supported, so that these details do not fall outside the scope.
Relative position of the layer joints
In two layers of swissporPIR Alu, the joints are offset relative to one another. In a single layer, the manufacturer recommends rebated or tongue-and-groove profiles on roofs. When assessing the completeness of the purchase, this offsetting of the joints must be specified.
When planning the purchase, it is worth establishing the relative position of the joints of both layers of swissporPIR Alu. Omitting this item does not remove the task, because tape on the surface does not recreate the missing core nor constitute independent waterproofing. The delivery of supplementary materials is intended to limit direct gaps through the thickness of the assembly without omitting other layers. Before approving the amount, agree the plan for both layers, the function of each seal and the scope of execution of the joints.
The profile does not replace support
The edge profile is not a structural interlock as in a sandwich panel and by itself does not determine the transfer of any span. When proposing a substitute, check whether the tongue-and-groove of swissporPIR Alu serves as the connection of the thermal insulation.
Assessing a substitute requires separating the tongue-and-groove fit from the load-bearing capacity of the swissporPIR Alu support — a similar name does not make the products equivalent, because the board’s interlocking joint does not entitle you to use any support spacing. The supplier’s data should allow correct bearing to be maintained even where adjacent elements join easily. In both quotations, compare the support of whole boards and the transfer of loads to the structure before you accept a change.
Polyurethane insulation: the right profile in the order
Where the edges differ, check how the usable area and the offcuts at the edges are calculated; the quantity ordered follows from the board layout, not from the rectangular area on the plan. The budget also covers the availability of swissporPIR Alu edge profiles from 40 mm thickness according to the instructions.
Before approving the price, confirm the availability of the swissporPIR Alu edge for the 20 mm variant — the profile described for thicker elements cannot automatically be attributed to it. In the order, specify the delivery designation, the covering area and the offcuts from perimeter processing, and price the missing work separately.
A case worth considering
Two quotations for swissporPIR Alu may differ in price also because they relate to different edges. Before choosing, you must establish which version corresponds to the design, calculate the cuts and check the availability of the appropriate thickness. A more expensive profile does not eliminate all work at the terminations, which is why a reliable comparison covers the finished connections and the quantity of waste, not just the name of the variant.






