Choose a material

Roofing sheets

Sandwich panels

PIR insulation boards

XPS

Accessories

Fencing

Polystyrene and thermal insulation

Comparing EPS prices per pack, square metre and cubic metre

At a glance

The price of a pack of polystyrene is not enough to compare offers. Packs can have a different volume, board thickness and covering area. First bring the prices to a common unit. Then check the parameters and the delivery cost. A cheaper cubic metre does not have to mean a lower cost of insulation that will meet the project requirements. The cubic metre makes it easier to compare the volume of material. The square metre shows the cost of covering an area at a given thickness. The pack is the purchase unit, but its size depends on the product. Each of these units is useful, provided it is clear what exactly the stated price covers. For two boards of the same thickness, the cost per square metre can be compared.

Packs and boards of white EPS with a calculator, documents and a tape measure when comparing prices

Which unit should you choose for comparison?

With different thicknesses, you first have to establish whether both variants provide the required insulation performance. Do not mix the net price of one offer with the gross price of another. Such an error can be greater than the difference between the materials themselves.

How do you convert the price of a pack?

Divide the price of a pack by its volume to obtain the price per cubic metre. If an example pack costs approximately €17.02 and holds 0.3 m³, the result is approximately €56.73/m³. This is purely an arithmetic example, not a current market price. The amounts were converted using the NBP average rate of 4.407 PLN per EUR dated 13 November 2026 and rounded to cents. For your own comparison, enter the values from quotations and packing tables.

To obtain the price per square metre, divide the cost of the pack by its actual covering area. The same example pack of 0.3 m³ at a thickness of 20 cm corresponds to 1.5 m². The calculation is approximately €17.02 / 1.5 = €11.35/m² after rounding. For the rebated version, check how the covering area is determined instead of assuming it from the external dimensions alone.

How do you compare different lambda values?

The thermal resistance of an EPS layer is calculated as R = d/λ. For the same target R, a board with a lower lambda value can be thinner. For example, for R = 5 m²K/W and λ = 0.038 W/(m·K), the required thickness follows from 5 × 0.038 = 0.19 m. For λ = 0.031 W/(m·K), the calculation gives 0.155 m.

This comparison covers the layers alone, not a finished wall. For purchasing, the available thicknesses must be selected and the whole design checked. Rounding to real variants will change the price and the thermal resistance achieved. The Uc-value relates to the building component and takes into account more than the polystyrene alone. It should not be attributed to a single board offer without calculations.

You can also calculate the price per square metre of the layer as the price per cubic metre multiplied by the thickness in metres. This makes it easy to prepare two cost variants. The condition for a fair comparison remains that the other requirements are also met, such as mechanical properties and compatibility with the thermal insulation system.

When does a similar price apply to a different material?

Façade and floor boards can have a similar lambda and yet serve different purposes. On the façade, the parameters required by ETICS are important. Under the screed, the loads must be taken into account. At the foundation, the action of moisture is added. The price only makes sense once products that do not suit the place of use have been filtered out.

So do not compare only colour, density or a large number in the name. Read the declared properties of the specific board. In loaded layers, CS(10) alone does not define the permissible service load. If the project requires long-term information, an offer without this data requires clarification, even when it is the cheapest.

How do you add delivery and the remnants of packs?

Compare the amount for the actually required number of full packages. Material sold in a larger pack may leave a larger surplus. Add transport, unloading and any separate delivery of the missing batch. For a small scope of work, these costs can significantly change the order of the offers.

Pay attention to the delivery date and storage location. A very early purchase requires protecting the material against damage and weather. A late delivery can hold up the crew. There is no need to assign random amounts to these risks, but it is worth noting them alongside the price. Agree the terms for accepting and returning full packs before ordering.

Will a cheaper board always reduce the cost of thermal insulation?

The cost of the entire assembly also includes labour, fixings, adhesives and details. A change of thickness can affect window sills, flashings and connections with other parts of the building. Not every change in lambda will therefore produce a saving equal to the price difference of the boards alone. Compare variants within the same scope of work.

Do not calculate the payback period from the pack price alone. Calculated heat losses, conditions of use and heating costs would be needed. For the purchase, a reliable table is enough: requirements met, quantity, unit price, delivery and total cost. Then you know what you are paying for and why one offer differs from another.

EPS boards are produced by, among others, Termo Organika, Austrotherm, Polstyr and Justyr. Compare specific parameters and the full purchase cost, without judging the material solely by brand.

7 branches. Materials closer to your project.

Izoprofil.com map of seven branches offering sandwich panels, PIR boards and sheet metal
  • SEROCK — Dzierżenin 34 E [mapa]
  • BŁONIE — ul. Sochaczewska 138A [mapa]
  • RADOM — ul. Grobickiego 8 [mapa]
  • ŁÓDŹ — Natolin 8 [mapa]
  • OLSZTYN — Barczewo, ul. Prosta 9 [mapa]
  • WROCŁAW — ul. Jerzmanowska 10C [mapa]
  • GORZÓW WLKP. — ul. Zielona 33/34 [mapa]

Check prices and availability: +48 500 409 109

Free quote

Materials for your project