PIR insulation
Buying IDELCO α-therm ROOF: compare the complete roof build-up
When buying IDELCO α-therm ROOF, the comparison concerns the complete roof build-up, not just the number of boards. The format affects transport, offcuts and work around numerous openings, so the cost is compared for the same plan and identical execution of the layers. α-therm ROOF is a rigid PIR board for flat roofs, faced on both sides with a gas-tight laminate on paper and aluminium layers. The terms “polyurethane boards” and “polyurethane foam” are broader than the PIR designation, so a supply enquiry should specify a flat roof build-up with this product in a paper and aluminium laminate.

α-therm ROOF PIR boards in a roof assembly
The fixing of α-therm ROOF is selected from the solutions approved within the system; the short name in the price list does not describe this, and the approval of several methods does not mean that the entire system may be freely substituted during installation. The choice is to allow the method of retaining the layers to be matched to the substrate and the use of the roof. Provide all tenderers with a description of the waterproofing, the fixing and the load path to the structure, so that prices relate to a similar task.
Board thermal resistance versus the result for the whole roof
Two α-therm ROOF offers may refer to different thermal resistances despite the same lambda of 0.022 W/(m·K). The catalogue table links a thickness of 100 mm with a resistance of 4.50 m²K/W, while 140 mm with R_D 6.35 m²K/W. When selecting the variant for comparison, keep this assignment of data to the board being ordered.
Before comparing amounts, read the lambda of 0.022 and the thermal resistance of the specific α-therm ROOF thickness; the cheaper item may produce a different effect, because the favourable result of the board does not cover the gaps at the parapet or the influence of the fasteners. Assess the height limitation without equating R_D with the U-value. In the offers table, include the selected variant from the 40–200 mm range and the calculation of the entire building element, and link the price difference to a specific change in parameters.
Polyurethane insulation with the right edge profile
The formats 1200 × 600 mm and 1200 × 2400 mm are available with a square edge or a rebated edge. When choosing, be guided by the geometry of the roof slope and the possibility of supporting the boards. In the measurement of the polyurethane insulation, take into account the difference between the square edge and the rebate in α-therm ROOF boards.
The profile and format of α-therm ROOF involve cut-offs around penetrations, so calculating from the rectangle area alone can be misleading — cutting on site changes the factory-finished end of the element. Prepare the cutting plan so that the joint remains correct also at the edges and at equipment bases. For the quotation, add a cut-off layout for the 1200 × 600 mm or 1200 × 2400 mm format so that the required details do not fall outside the scope.
Fixing, bonding and ballast
In a ballasted roof, calculate the weight of all layers and check how the forces are transferred to the structure. In a bonded system, the compatibility of the adhesive with the facing and the substrate is decisive. For the completeness of the purchase, state the weight of the ballast or the bonded connection above the α-therm ROOF board.
Assess the completeness of the offer for the entire roof, in accordance with the method of securing the covering above α-therm ROOF. Ballasting introduces different loads than a bonded or mechanical connection, and an omitted item does not disappear from the task. Delivery of supplementary materials allows the support and accessories to be determined before ordering. Before approving the amount, agree the load distribution, the compatibility of the adhesive with the laminate, the substrate parameters and the scope of making the connections.
Product class and assessment of application
α-therm ROOF achieves a compressive stress of at least 150 kPa at 10% deformation. The product data sheet alone states reaction to fire F for this board. When proposing a substitute, compare the class F of the α-therm ROOF product with the result of application on sheet metal, stated separately.
When assessing a substitution, separate the α-therm ROOF product class from the result for use on sheet metal. The B-s2,d0 result for the specified assembly does not make every board with a similar name non-combustible. In both quotations, check the description of the assembly covered by the assessment and the CS data of at least 150 kPa before you accept a change of solution.
Insulation with polyurethane: the exact order version
The order should use the current name α-therm ROOF and specify the edge variant. The designation I-ROOF found in older materials must be checked against the current documentation. Before setting the budget, confirm exactly which product the quotation covers.
Before approving the price, check the version of the documents and the designation of the α-therm ROOF board offered; a historical name does not confirm the parameters of a new delivery. The schedule should specify one variant together with the required layers. In the order, confirm the product data sheet, thickness, profile, format and the complete scope of the roof, and price any missing work separately.
A case worth considering
When purchasing α-therm ROOF, you can compare the 1200 × 600 format with 1200 × 2400 mm. The larger board reduces the number of elements in a simple field but requires appropriate access and handling. In surroundings with numerous openings, a more precise cutting plan will be needed. It is worth calculating both variants on the same plan. The cost of offcuts and handling may change the assessment of the price per metre alone.






