PIR insulation
Buying PIR and XPS: a lower price per square metre or the right product?
The price of PIR and XPS is only comparable when both variants meet the requirements of the same location. A similar format and thickness are not enough. PIR boards can reduce the height of the build-up, but the value of this benefit depends on the detail. The offer should also show the costs needed to complete the whole. A thermal comparison should refer to an identical R or an identical available thickness. These are two different questions. At the same R, you check the space required and the cost. At the same thickness, you assess the difference in resistance. Both results make sense if you do not mix them in one table. First determine the thicknesses for a common thermal target, and only then compare prices.

The advantage of PIR lies above all in the space
Polyurethane boards with a lower lambda may require a different quantity of material than the selected XPS. This does not mean a fixed percentage advantage for every PIR offer. You have to use the data for specific products. It is also worth checking the available commercial dimensions, because the theoretical result of a calculation does not always correspond to a thickness that can be ordered.
Contact with water matters more than the appearance of the core itself
XPS includes products intended for perimeter insulation and inverted roofs. However, such an application should not be extended to any board bearing this abbreviation. Similarly, for PIR the range specified for the specific product applies. The installation location must be supported by the documentation, not merely by a similar appearance.
If the application involves water, the document confirming the correct scope is part of the offer’s value. A cheap batch without identification may not provide a basis for selection. Polyurethane insulation should not be given the characteristics of another product found on the internet. The same applies when assessing the remaining stocks of XPS. Before purchase, establish the exact variant and its condition. Without this, the saving is difficult to compare with a material with confirmed properties.
CS and creep do not describe the same situation
For a given application, compare the appropriate variants, not extreme products from catalogues. XPS with high compressive strength and a lightweight PIR board for a different purpose do not form a fair comparison. You must first establish the requirements and then find the variants that fulfil the same range of functions.
In the floor or on the roof, check whether both proposals correspond to the loads envisaged. Polyurethane foam with a given CS is not automatically equivalent to any XPS with a similar figure in the description. What is needed is a consistent meaning of the parameters and an assessment of long-term performance. If one variant requires additional load distribution, add its cost. Otherwise, the price of the insulator conceals the difference in the scope of the entire solution.
Facing and fixing limit the scope for substitution
In the documentation, it is worth recording the exact surface variant and the method of fixing. This makes it possible to compare the offer with the execution requirements. Adhesion should not be improved by randomly removing the factory facing. Such an action can lose the properties for which the given board was selected.
Include adhesives, fixings and any separating layers in the comparison. A change to the board surface can change the required set. Do not assume that materials purchased earlier will fit the new offer. It is worth asking for a full list before approving the order. An additional purchase and a delay to the works also have financial significance. An apparent saving per square metre of board should not obscure these foreseeable expenses.
The most common situations in which the choice is justified
In one building, different insulators may be needed. The material under the roof waterproofing does not have to be the same as that envisaged in the ground. Such a selection is justified if each section meets its own requirements. However, the connection of different systems must be carefully resolved.
The quotation may cover different materials in different parts of the building. It is worth leaving PIR boards where the thickness constraint brings a concrete benefit. A suitable XPS may meet other requirements. Such a combination does not require artificially standardising the entire order. However, the number of deliveries, packaging and junction details must be taken into account. Material savings should result from actual quantities, not merely from an attractive unit price.
Compare systems with the same function
A sensible decision may lead to PIR in one section and XPS in another. There is no need to force a single material throughout the building. What matters is the correct combination of functions. This approach makes it possible to use the low lambda of PIR without ignoring the special operating conditions of other parts of the building.
Compare the final cost for the completed function of the building envelope. Insulation with polyurethane may reduce the scope of reconstruction at the threshold or flashing, which is worth pricing separately. If this benefit does not exist in a given location, it should not be assigned a nominal value. Two complete quotations show both the advantages and the necessary work. The choice then results from a transparent comparison, not from a general conviction about the superiority of one plastic.
How to prepare a complete comparison of offers
An offer for a cheaper product may require a thicker layer and larger flashings. The second may have a more favourable lambda but not suit the moisture conditions. First reject the technically unsuitable variant. Only then compare the remaining solutions by price.
Prepare a table covering the product, the required resistance, the thickness, the quantity and the full installation. Add conditions relating to water and load. Only once these criteria are met should you compare the price. PIR boards may prove justified thanks to the space saving, but they need not be presented as a replacement for every XPS. A good quote allows you to check the reason for the choice and its total cost. That is more important than one item being cheaper in an incomplete price list.






